Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi Experts, Could you please suggest if this is a valid ACL statement.   I want to restrict access from vlan20(172.20.2.0/24 Network) to other vlan. Also need to permit access to my WAN Devices which is of ip address, 172.20.4.2,172.20.4.4 and 172.20...

Hi,I need restricted access to another VLAN for TFTP traffic. So I´ve created an ACL like this:permit udp 192.168.30.0 0.0.0.255 host 192.168.40.10 eq tftpI add this ACL to the source interface (192.168.30.0) as INCOMING.The tftp request to the tftp ...

Hi,   From the “Cisco Industrial Ethernet 4000, 4010 and 5000 Switch Software Configuration Guide”, “Chapter: How to Configure EtherChannels”, https://www.cisco.com/c/en/us/td/docs/switches/lan/cisco_ie4010/software/release/15-2_4_EC/configuration/gu...

EE_36220 by Level 1
  • 868 Views
  • 2 replies
  • 0 Helpful votes

Hi friends  we are using  sonicwall NSA 2400 series firewall with 46 mbps leased line connection. most of the time my firewall cpu utlization gets nearly 98 percent . due to this my network is getting struck. we are using 2 cisco 2960 series switch. ...

prince.p by Level 1
  • 626 Views
  • 1 replies
  • 0 Helpful votes

Hi. every body    I've any question about concetp switch stack   1. I've 2 switch stack.   If swtich stack master is fail . when show interface status  in switch , how is it the port id  ?  G1/0/xx , G2/0/xx    2. If i'll upgrade ios on switch stack....

bird_th by Level 1
  • 875 Views
  • 2 replies
  • 0 Helpful votes

Hello all I just recently run the really great Cisco CLI Analyzer on one of my Nexus switches, where various servers, including VMware ESX ones, are connected to. The tool then showed me a "Danger"classified event, named "NXOS Spanning Tree Health Ch...

patoberli by VIP Alumni
  • 2818 Views
  • 1 replies
  • 0 Helpful votes

hi all,   i have pair of nexus switches with vpc enabled. i have connected one L3 link to avoide L3 routing issues in the nexus vpc design. i have created one vlan in the nexus and the same subnet i have created interface in fortinet firewall. the fi...

zeuscyril by Level 4
  • 2379 Views
  • 3 replies
  • 0 Helpful votes

Hi, Do you think this is important which router should RP be configured at?  As we know, after RPT established, it will switch to SPT. And we can also control traffic at RT. Once it exceed the threashold, it could be switched to SPT. Do you think so?...

wfqk by Level 5
  • 999 Views
  • 5 replies
  • 0 Helpful votes

I have installed cisco2911 router and whenever i restart the router,I am getting the error 'PA-3-PA_INIT_FAILED: Performance Agent failed to initialize (Missing Data License)' why this error is showing and also this may cause of network disconnectio...

Resolved! QoS on Tunnel IPIP

Big question:  Does the config below work? We have issues with WRED statistics.   Environment: Two branch locations that use MPLS to connect to a datacenter. The configuration of QoS is applied from CE in the datacenter.  Branch uses VOIP and some Co...

stevebt28 by Level 1
  • 3961 Views
  • 22 replies
  • 0 Helpful votes
Unanswered Topics