See the attached: Cant figure out why the tunnel had a 'down' protocol. If you need more info from the routers...Let me know. Thanx Team.
See the attached: Cant figure out why the tunnel had a 'down' protocol. If you need more info from the routers...Let me know. Thanx Team.
Hello, We are trying to configure default Q-in-Q in a cisco 93180yc-ex however following the steps at nexus 9300 configuration guide we are unable to suceed. The topology is the following: Router1 (g0/1) <-> (e1/1) Nexus1 (e1/48) <-> (e1/48) N...
I have L3 3750x Switch. i am not able to run internet on that. 1) I have to create VLAN 100. (which i have created) 2) Then need to create DHCP pool 192.168.1.0 (i have Created DHCP pool & merged with vlan 100) 3) i have series of wan ip one of tha...
Buen dia, alguien me puede ayudar, con respecto a la siguiente configuración por favor. intento hacer una VLAN, con un Switch Cisco SG300 L3, les comento que tengo creada las VLAN, lo que no consigo es lo siguiente : dar DHCP a las VLAN y hacer que ...
Hi. We setup the following in a interface trunk: storm-control broadcast level 5.00 storm-control action shutdown storm-control action trap spanning-tree guard loop Aster a few days the interface went down. Do you know how can we determine what cau...
Hi there Attached herewith is my OSPF network template (Image 1). Everything is working very good. PC-1 can PING PC-2 & OSPF is following best possible costs. When I PING PC-2 to PC-1 (& vice versa), the packet follows path as attached in image 2. Bu...
Hi,We have Cisco 3850 switches and we dont use dot1x but we need to turn off ip device tracking but when I do it from global config mode it pops up the below error:Switch(config)#no ip device tracking % IP device tracking is disabled at the i...
Here is my current configuration for Netflow on my 3850. My question is posted at the bottom. flow record FNF-input: Description: IPv4 NetFlow No. of users: 0 Total field space: 56 bytes Fields: match ipv4 tos match ipv4 prot...
Hi, I think I know what needs to be done for this but am not 100 percent sure. The end goal is to make sure af41 packets are getting remarked to af31 going outbound to our mpls provider. currently the following class and policy maps are configured...
Hi We have a server that has a iLO that will only support 100MB at present we only have a Nexus 3548 in our rack and wondered if there was any way to connect this to the Nexus which seems to only support !GB and above ? Any workarounds that people ar...
Dear everyone!, My switch is 2960X cannot start after I config wrong and loop reboot everytime. I was download new IOS: c2960x-universalk9-mz.152-2.E6.bin but nothing change. Everyone help me pls! Connecting to COM6...Connected. Err: Interrupt: Mach...
hello i have cisco 860 router i have an DHCP service working on it. when i plug a two devices onto a Lan network it getting IP addresses from the DHCP but if i replace a "broken" device with "another" device( so total devices on my LAN network remain...
Hi Team, I have L3 switch ,in this switch i created L3 vlan id -10 and assigned few Ethernet interfaces to this vlan. If I delet the vlan 10 using " no vlan 10 " is this also remove the ethernet interface config for that vlan? or just it put the i...
ecan anyone xpalin me about ospf stub and nssa area and the difference between themRegardsBava
Hi! I've discoverd a strange behaviour. Either it's a bug, or an urgent required upgrade of my knowledges. C2960+ 24TC-L / 15.0(2) SE6 Here is the symptoms observed: . If i try to export the startup config to a TFTP server located in a distinct vlan...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-25-2024 10:55 PM | ||
08-25-2024 03:03 PM | ||
08-25-2024 06:37 AM | ||
08-20-2024 09:12 AM | ||
08-06-2024 12:40 PM |
User | Count |
---|---|
5 | |
4 | |
4 | |
4 | |
4 |