Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! Problem with last client in VLAN subnets

I have this network setup (pic below) in packet tracer and the last client [PC3] can't access any other part of the network, the other 2 are receiving DHCP and can ping. My configuration is this: R1: enconf tint g0/0.1enc dot 10ip add 192.168.1.1 2...

Fiber and Wireless Project Deployment

Hello EveryoneI need a suggestionWe have 50+ sites in different locations and we are going to deploy a separate network for the communication between the sites.all the sites are having (fiber as primary and wireless as secondary) redundant connectivi...

Resolved! Switch trunk port to sonicwall

The switch is configured with access vlan 10 and voice vlan 20. To connect this switch to the firewall (sonicwall), I guess I need to configure fa0/1 as a trunk port, and connect this fa0/1 to the sonicwall's lan port. How should I configure the soni...

mark l by • Level 1
  • 6972 Views
  • 2 replies
  • 0 Helpful votes

Cisco 4500-X VSS and Proline SFP-10G-SR-PRO SFP+

Hi, I have the following problem and I've reached a point where I don't know what to do anymore. Scenario: 2 x Cisco 4500-X in VSS mode. 2 x VSL Ports - 10G with SFP+ (Proline SFP-10G-SR-PRO) 1 x Dual-active fast-hello Port - 1G with SFP (Proline G...

Calin C. by • Level 5
  • 2258 Views
  • 5 replies
  • 0 Helpful votes

Resolved! Difference between Cisco Catalyst 48-port full PoE and Cisco Catalyst 48-port UPOE models

Hello guys, The information below can be found at the page 21 of the "Catalyst 3850 Switch Hardware Installation Guide": "Depending on the installed power supply modules, each port can deliver up to 60 W of Cisco UPOE. See the Power Supply Modules, ...

apereira3 by • Level 1
  • 1795 Views
  • 5 replies
  • 0 Helpful votes

4500E per slot bandwidth

Dear Experts,  I saw in datasheet that SUP-8E supports 48 Gbps per slot bandwidth. Does this mean we dont have line rate performance on below modules? WS-X4712-SFP+E: Cisco Catalyst 4500E Series, 12-port 10 Gigabit Ethernet (SFP+) WS-X4606-X2-E: Cis...

Resolved! Asa 5505 vpn configuration

I have Cisco ASA 5505 this router has public IP address so it's visible in internet.There is also Windows server phisical machine connected to that router which also contains public IP. However what i have to do is create VPN on that ASA that would a...

Arie by • Level 1
  • 1887 Views
  • 12 replies
  • 0 Helpful votes

Resolved! Inquiry on ASA 5525X - Similar to load balancing or round robin (dual ISP implementation)

Hi Team, Good day. Any one who is familiar with  the feature and capability of ASA 5525X with firepower. We have two (2) ISP directly connected to ASA 5525X  which is currently configure active and standby. Is it possible for our windows client to do...

SPAN port on distribution 6500 VSS

Hello folks,We would like to capture the traffic from the access switch 4510 on security appliance which has sniffer installed. It has 10G ports on it. I tried configuring on distribution 6500 VSS to capture the traffic from the access switch 4510 bu...

Resolved! QoS behaviour ?

Hello, we had a case whereby a client on the LAN initiated a large data transfer with source traffic marked as EF. It then flooded the 100Mbps WAN uplink.No other clients could pass traffic. I thought the service policy I had on the WAN uplink would ...

View All
Review Cisco Networking for a $25 gift card