Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...

Hello All, We have this vlan 1215 on switches. These were newly created.There are no access ports assigned against them yet , but they do have trunks on them.The gateway for this resides on a firewall and the trunk through it has been enabled for ab...

suthomas1 by Level 6
  • 812 Views
  • 1 replies
  • 0 Helpful votes

We are setting up EIGRP for gateway failover to a redundant data center and I'm having issues getting EIGRP (or OSPF for that matter) to form an adjacency.  I've attached diagram of our setup but a brief description below: Campus LAN eventually hits...

Hi,recently I bought 4 ws-c3560-24ts-e reforbished from eBay and It has ip base IOS installation. The only reason that I got this It's because this model should support Ip service IOS.My questions is could i install IPS ios on this without any paymen...

attar0001 by Level 1
  • 896 Views
  • 5 replies
  • 0 Helpful votes

POE

Hello everyone, I have a 3560 switch that is not supplying POE to my devices, access point and switch. all the ports are poe auto an the show power inline command is as follows. Available:0.0(w) Used:0.0(w) Remaining:0.0(w) Interface Admin Oper Powe...

Hi I am trying to get my head around the bandwidth and throughput stated on the cisco documents when searching for which router to buy. So I have seen routers (e.g ISR 4351) that has a performance rating of upto 2GBPS, yet you can have a module inst...

Hi All,We are using three 3750X switches in stack. we are seeing the cpu spike is reaching 100% once in a 2 hours or three hours . But the average CPU is upto 40% only . we are using this switch as L2 and L3 also with PBR. IS this spikes are expected...

When will a packet get tagged?I have attached 3 network architecture diagrams(Image 1, 2, 3). Configurations:Image 1: Both L3 switches were in default VLAN's and no trunk link present between them. All the access ports were left to default including ...

Vignesh M by Level 1
  • 12708 Views
  • 9 replies
  • 0 Helpful votes

This is related to another question I asked on here but more specifically about ARP on the network... I have a network of 8 SG300-52 switches.   I have around 200 active IPs on the network.  (Yes there are a lot of unused ports on the switches) I am ...

Hello,  See attached. When I issue the sh ip ospf database command, the output lists the LSA types. Under LSA 1(Router), it lists that the Adv Router 10.255.255.254 has 5 links and when I issue the sh ip ospf int brief command on the same router, i...

zekebashi by Level 4
  • 550 Views
  • 1 replies
  • 0 Helpful votes

Resolved! OSPF LAS Types

Hello,  See attached. When I issue the sh ip ospf database command, the output lists the LSA types. Under LSA 1(Router), it lists that the Adv Router 10.255.255.254 has 5 links and when I issue the sh ip ospf int brief command on the same router, i...

zekebashi by Level 4
  • 771 Views
  • 2 replies
  • 0 Helpful votes

I made a upgrade for c7600. However the firmware still on 12.2, on the RSP, and Line Card. Any one know, If we need to upgrade the firmware too, and what is the procedure...? hostname#show moduleMod Ports Card Type Model Serial No.--- ----- ------...