Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, February 2, 2026, through Friday, February 20, 2026. Our colleagues Amruta Navadagi, Anaya Kalawat, and Mohammad Mehtabuddin will be waiting to assist you...
vxlan configuration between 9600 core switch which is the l3 ip address that connected to 9500 distribution switch in that ospf is enable that connected to l2 switch 9300 that connected to firewall how to configure the vxlan for this.
Hi, We have a ACE, which we use to load balance traffic between towards two Proxy servers. We are using source nat in proxy interface Vlan in ACE. Two days back our manager enabled ssl3 in proxy servers after that clients are getting SSL error secur...
Hi Team,I am in the process of configuring Cisco Ethernet Switches (IE3x00 Rugged Sefor the project and would like to know do we have to leave the memory card inserted during /after setup process. If not then ,Can it be used just to take the backup ...
Hello All, My network team updated layer 2 security configs on a Nexus Switch 3172(not stacked) and some of the configs (ip verify source, dhcp snooping, ip arp inspection, block unicast) knocked off connectivity to some VMhosts on VCenter. VCenter ...
Hi in nxos 9.3.12 i have many routes /24 /21 /20 have bgp community no-exportNow i want Create bgp Session with ASX and announce all routes to ASX ASX is ebgpHow can do this by route-map ?? route-map no-export, permit, sequence 10Match clauses:ip add...
Weird issue here. I have 2 Nexus 9300 running version 10.1(2) and both are encountering the same issue. I am setting up Radius on them and have entered all the info for the servers, groups, and associated access rules (such as "aaa authentication log...
I have a DHCP server in my project which gives all ip, also I need to make 4 pc which will have static ip, and I need to ping them with pc which has dhpc setting on pc with static ip how can I do it? I have one router. for examplePC59 > PC30PC30 ping...
Hi I am a newbie here, We have two networks having geographically distant switches (IE2000) daisy-chained using the fiber network. I would like to connect these two networks with the same chain to be accessible from my server(added both network IPs i...
Is this command rate limit the traffic passing through switch port.srr-queue bandwitdh limit 90srr-queue bandwitdh limit <10-90> enter bandwidth limit for interface as percentage. If I want to pass 9 mbps traffic through a switch port what command i ...
Guys, I didn't see any configuration problems with the LACP, the SFP or the link/fiber.But I have a topology with a LACP between 9500 x 9400, and I use 4 10G-SR interfaces. One of these interfaces is passing TX input traffic, but not RX output. I re...
Hi,I've been playing around with spanning-tree BPDUguard for a topology that has 3 switches connected on both GNS3 and PacketTracer, and both depicts the same:Topology:SW1---SW2---SW3Config:The switchport status for the SW2's interface connected to S...
Hello, PLease consider above topology, it has a Router, IE-4010 switch and it is performing L2NAT. All the PC connected to it are a part of Same VLAN-20 and PC - A-B-C are translated to some IP in the screenshot. PC D has the IP in the same subnet ...
Hi I'm a student doing an assignment rn and I think I did most of the steps right but I can't ping PC B from PC A and I cant ping PC A from B. It keeps saying destination host unreachable. Here is my file can someone please help me out and thank you ...
HelloI just got a second hand Catalyst 6800IA-48FPD switch and i wanted to know the following:1-What is the latest compatible stable firmware update for this specific switch model i could apply? Either I couldn't find it or the cisco website doesn't ...
Hello everyone, could you help me with commands to determine if a Cisco IOS XE router has any password expiration controls configured. I have tried several suggested commands and I cannot determine if there is any line with which I can support that t...
