Hello,I have a Cisco 4010 Ethernet switch that is currently connected to a Moxa EDS-208A. The 4010 interface is an access port configured as below: switchport mode accessswitchport access vlan 50The Moxa switch only has hosts connected to it, and doe...
Forum Posts
Hello all I am currently facing a problem when trying to remove the switch from the stack, as I tried all the commands but it still does not switch to standalone mode. When the switch is restarted, it goes to the elections and config is lost....is...
Recently my company has bought 4 new cisco switches. 2 CBS250-48P-4G's and 2 CBS350-48P-4G's. In the past we have just used RJ-45 copper connections to daisy-chain the switches together for interconnectivity but with these new switches we were hoping...
Hi Everyone,i'm currently facing a really strange problem, i'm running a simulation in GNS3 with the following TopologyThe Switch to which everything is connecting (N301SWC01) is the coreswitch, the 2 other Switches that it's connecting to are the ac...
Resolved! SVI VLANs
Hello Expert,I want to enable DHCP for multiple VLANsThis Lab aims to create multiple SVI-enabled, DHCP and add more switches to the core switch, and create HSRP.What is the best practice for creating multiple VLANs It should be on the access layer o...
Please Help. Trying to apply this ACL to the outside interfaces for inbound traffic. When applied, both outside interfaces (ISP's) pass no traffic. object-group service SERVICE-PROTOCOL-PORTdescription Ports to Allowgre eq 50gre eq 51tcp eq 500tcp e...
If the server is set to 9000 MTU and the GigabitEthernet port on Cat 6500 is set to default (1500), would the traffic between the two drop completely, or it would it be dropped only for frames sent above 1500 or the traffic would flow normally unaffe...
Dears, I am trying to setup MAB (MAC Authentication Bypass) on my new switch C1300.I cannot find the right documents to do that. Any help? Thank you in advance
I understand that spanning-tree portfast configuration is designated for end devices, so all in access mode.From an article I learned that spanning tree portfast is also avalable for trunk links.However I can not think of a situation that would make ...
Have a bit of an odd situation with an SG300-28P.The switch performs just fine when connected to various peripherals (local PCs, media players, etc) however is thrown into a reboot cycle as soon as it's connected to the larger building network by way...
Hi All,I have found recently that Cisco 1905 router is having a throughput of only 10 Mb. But the router is having 2 Gig ports!.My understanding is that throughput is the data packetforwarding done by a router at a time.What is actually mean by throu...
I am seeing IP Address 127.0.0.x is being discovered in our NAC solution generated from C6509-E with SUP2T and the IOS version is 15.5.1SY10.Is there any specific command to display from where this ip address is being generated on the VSS switches?
Hi Guys, Could you please advise if my thinking is correct. I'm preparing for migration and the core will be replaced by firewall. I need to estimate the throughput requirements. I've run show hardware capacity fabric-utilization and got the result ...
HI team , working on Private vlan configuration in EVPN-Vxlan Fabric I have leaf1 port24 ---host1, leaf2 port 24---host2 primary vlan id 400 ,, community vlan id 402Leaf1-port24 and leaf2-port24 are put in vlan402 as belowswitchportswitchport mode p...
Hello, we are working to install new C9410 chassis and would like to know if anyone has gone through a SSO event in production? The configuration we are planning is a single link to each sup.I would specifically like to know what happens in this situ...
