Switching

We have two sites: 192.168.100.x and 192.168.101.x currently connected  via IPsec VPN. On each end we have a Cisco ASA 5505. However, each site  also has an MPLS VPN with intentions to move all traffic to this link. Site A: ASA inside interface is 19...

Hi Guys,If I need to increase the maximum hops on our MST L2 network do I just need to do it on the root bridge or do I need to do it on all the switches within the MST instance?spanning-tree mst max-hops 30Thanks,Ross.

Dear cisco!We have 2 switch 3750: WS-C3750-24PS-S and WS-C3750G-48PS-SWe using stack cable to connect 2 switch above, then WS-C3750-24PS-S plays role master and WS-C3750G-48PS-S plays role slave.So we config FE 1/0/9 and FE 1/010 on WS-C3750-24PS-S n...

hello all:I have the folowing setup:•1.       Cisco 3560 x1 •2.       Cisco 2960 x2 •3.       Juniper SSG 140And I have 4 environments:•1.       DR_UAT_AIX•2.       DR_DEV_AIX•3.       DR_UAT_WIN•4.       DR_DEV_WINAccordingly I configured 4 VRFs as ...

Dear Cisco community,as my Netgear FVX538v2 router recently died I would like to replace this router by an enhanceable Cisco product. I'm thinking of a Cisco 2901 model that will be connected to the cable modem of my ISP and has to support PPPoE over...

Ok, I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:http://www.cisco.com/en/US/products/hw/switches/ps607/products_tech_note09186a00800c4546.shtmlI have tried "...

Hi, I'm trying to understand Summarization aka Route Aggregation. I don't understand what is it that I'm mistaking in this exercise:"Find the summary address and mask of the following set of networksa) 172. 148. 0. 0/13 through 172. 156. 0. 0/13"MY A...

Hi.I'm doing a practice lab for spanning-tree but I'm confused about the output of the sh spanning-tree command.I've attached an Image.  I don't understand how the cost to root Is 4 for both vlans when the route to the vlan 12 root switch crosses 2 s...

Dear All,I have cisco 4510R-E core switch in that i have WS-X4306-GB module now i have to connect S.M fiber through coreswitch to my another location (1KM) having HP X120 1G SFP LC LX Transceiver (JD119B.).Now please suggest me which module i have to...

So I am trying to get traffic from 192.168.1.33 on UDP ports 10000-20000 and port 5222 (udp) to have DSCP set to EF and  Forwarded accordingly.   Any thoughts?            Building configuration...Current configuration : 32481 bytes!! Last configurati...

HiI am facing issue with http login after IOS upgarde on 3750 switches. I upgrade IOS from c3750-ipbase-mz.122-35.SE5.bin to c3750-ipbase-mz.122-53.SE2.bin Kindly let me know is there any other commmand i have to run.Regards Sunil

Basically, will adding a new area (in this case, NSSA totally stub) cause a reconvergance in Area 0? I don't believe so but was asked to check by adding a new discussion. More details:1) The links to the new area will be defined as Pt-to-Pt2) The stu...

Hi All,On 7606 with RSP720, I've configured bunch of eompls circuits. This is a multivendor equipment lab but There is also one circuit towards another 7600 box. 7601 and 7602 is directly connected.  7601 ( Lo 2.2.2.2) . 7602 (Lo:17.17.17.2)  Both ar...