Switching

Hi,We will deploy a wireless based network for our new plant soon.most of the users will use wirless instand of wire cable except servers.all the phones will use wireless also (Cisco cius)Here is my question.How can we setup QoS on wireless enviroume...

Hi, I have Cisco 3560X L3 switch and i need to configure DHCP on this switch. I have already configured below mentioned VLANsVLAN 10 - 192.168.8.254 (USER VLAN)VLAN 20 - 192.168.152.254 (REMOTE & VPN USERS VLAN)VLAN 30 - 192.168.0.254 (SERVER VLAN)Af...

wht is the difference between WFQ and CBWFQ From my understandingCBWFQ is using WFQ algorithmWFQ dynamically allocate queues , but CBWFQ statically assigned queusCBWFQ conversations are same as flows in WFQanyother comments ???

Hello everybody,What is the exact command in restoring the running-config on a Nexus 7010. Is it thesame commnd / procedure as the Cisco IOS?      Please help and Thank you in advance.--chie

hi,I would like test multicast routing with cisco1801.i create 2 Vlan. Vlan 200 (192.168.200.x) affect Fastethernet 1, Vlan 130 (192.168.130.x) Fastethernet 5.Version IOS is : adipservice-k9 124-9.t1ip multicast-routing#int Vlan 130 ip address 192...

Hi ALLI have a strange problem which i am pretty sure is quite easy to fix, because I think I am just over looking something or doing something completely dumb.Heres the problem, I have this cisco 4507 switch that I need to configure multiple ip rang...

For some reason nothing is being routed on my router in the cisco packet tracer.I have been researching online and I have realised that I need to enable IP Routing, is this the problem? Although when I followed instructions online, this is what happe...

I am trying to monitor a Cisco ACE modulen (A2 1.4a) connections (failed, current etc..) the following OIDs from Mib: CiscoEnchancedSlbMIB cesRserverTotalConns 1.3.6.1.4.1.9.9.470.1.1.3.1.17cesRserverFailedConns 1.3.6.1.4.1.9.9.470.1.1.3.1.18cesRser...

HiJust wondering what the current thoughts are on the following common problem  .......Have 3 x L3 distribution pairs (#1, 2 and 3) with a number of fully redundant L2 access switches off each Distributions are connected via a L2 core VLAN X is root/...

Hi, i have 2 routers connected to one switch via fastethernet ports. I want all the traffic to go through Router 1, and i wand Router 2 to be a standby router. could any please help/guide me with this?

I have a computer service shop and recently upgraded our network.  Since then i've been having issues when other computers are updating, the whole network slows down to a crawl.  If any 1 Mac is updating, the whole network drops down and I can barely...

Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this...

Does any one know how to set up a range loop back test on a 3750 switch?I am trying to test the switch port internally but can't match loop back to a port? Any idea and thank you.Sent from Cisco Technical Support iPhone App

on-plus see the device and allows CPE( imbedded) to start then never opens,,,tried genera connection and used that address supplied to open CCP    no discovery...any ideas....also seems onplus doesn't see a service contract or firmware, etc          ...

Hello.I am reading a document about supervisor redundancy and it mentions that The active supervisor engine synchronizes its run-time image with the standby supervisor engine if the time stamps of their respective run-time images differ when the syst...