Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Having trouble understanding the allocation of bandwidth  priority on a policy map in a cat 4500 supervisor 7Epolicy-mapclass-voicepriorityclass-bulkbandwidth remaining 10How does the bandwidth for priority get calculated?

whanson by Level 2
  • 558 Views
  • 1 replies
  • 0 Helpful votes

Dear All,            I have WS-C3750-48PS-S, i wanted to implement GLBP on this switch, Is it possible to configure GLBP on this switch?IOS :                    c3750-ipservicesk9-mz.122-55.SE4.binPart number:     WS-C3750-48PS-Swhile booting....Wait...

Hello Everyone,I am wondering if you could help me with an issue I am having for a client. Ok, so this client has a new 6500 fully created with VLAN's and the goal is to move clients over one at a time. I have configured the 6500 fully from start to ...

we purchase only Cisco Supervisor Engine VS-S720-10G and use it in our old C6509-E chassis.Now the supervisor engine was dead,(means not working and no LED's are ON). How can i claim the RMA from cisco?We purchase from one of our partner. We send it ...

In a switched layer 2 network of all Cisco switches (2950/60s, 3550s etc) how can I determine what VLANs are no longer used?What I mean by this is, VLAN 123 maybe defined on every switch, but if each switch has no access ports in this VLAN, then I wo...

jwbensley by Level 1
  • 2048 Views
  • 5 replies
  • 0 Helpful votes

- I have an older router 2600 running 12.1(4) IOS.- There are a few clients connected to it via the frame relay connection.- There is an IP that clients access 192.168.1.10 for example- We need to do a NAT for this IP for one specific client only lik...

ALIAOF_ by Level 6
  • 907 Views
  • 6 replies
  • 0 Helpful votes

I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error - % Error: Unable to create flash:/microcode_update% Error: It must not already existNormally, getting an error during POST isnt...

I have three 4506 switches with vlan 4 set as the management vlan. Switch 1 is connected to switch 2 and switch 3.I can access switch 1 and 2 using telnet from the management vlan and both switches reply to pings. But from switch 1 or 2 I cannot ping...

wn1kbates by Level 1
  • 3427 Views
  • 28 replies
  • 0 Helpful votes

Dear All,I need a L2 switch with dual AC power supply and RJ45 uplink The optin I got was   WS-C3560X-48T-L + C3KX-PWR-350WAC , but the problem is with uplink . There is no RJ45 1G uplink , there is only option for SFP uplinkThe another option was  W...

Haris P by Level 4
  • 10984 Views
  • 3 replies
  • 0 Helpful votes

Hi, I have a question about the two RPS2300 cables, because there are so many different statements about it, even in the official documents.So, I need the correct RPS2300 cable for a WS-C3560G-24PD-S and one for the WS-C2960-24PC-L. WS-C3560G-24PD-S ...

miwa by Level 1
  • 1275 Views
  • 1 replies
  • 0 Helpful votes

He All,I am starting to build a new Cisco Core 6513-E with Redundant Sup 720-3B from a currently running 6513 Core with Hybrid CatOS with 2 redundant sup2's. My question is probably really simple.How is Redundancy between the MSFC (Sup2) model differ...

Hey all,Need some help on the best way to configure rate limiting and/or traffic shaping for a single interface.Have a C3750-12S with an interface connected to a 10Mb circuit (leased line)  10Mb is shared over a 2 business units who respectively want...