tell me about working of different layers of internet protocol suite---Posted by WebUser Razi Hassan
tell me about working of different layers of internet protocol suite---Posted by WebUser Razi Hassan
If I configure two 3Com switches to run lacp on all ports, I can then connect any ports between the two switches and they will automatically determine which ports they share and turn those ports into a channel.With Cisco switches it appears I have to...
Hello everyone, I'm trying to figure what to do in this case which i'll expand:We have a WS-C3750E-24TD with the following features:- Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(46)SE, RELEASE SOFTWARE (fc2)- License Leve...
hi:i am back with another question. above is the scenario, the IP addresses of 4 PCs were assigned by DHCP. and each PC represent a vlan . question :how to block all incoming traffic to 192.168.99.0/24 except from 192.168.1.0/24 .ip dhcp excluded-a...
Hello all,Here is the hardware configuration:Switch Ports Model SW Version SW Image ------ ----- ----- ---------- ---------- 1 54 WS-C3750X-48P 12.2(53)SE2 ...
Hi, i am Trying to disable EIGRP on interface, but its not working. can any one help , if i am missing any thing?Diagram is attached.what happening is , i only want EIGRP neighbor to form between CORE 1 and CORE2 via direct trunk cable.But EIGRP is f...
I'm adding another module, WS-X6724-SFP, to our C6506E core switches. I read that it is hot swappable. But just wanted to get inputs from anyone if you encountered any issue or things I need to look out for. Thanks.Regards,Ramon
Hi.I'm doing a lab where I have to give a router an IP address In a zero subnet.I receive a bad mask error from the CLI and so I assume the no ip subnet-zero command Is In effect.Is there any way to see If subnet zero Is enabled other than this ?Than...
Can someone tell me which process is consuming high memory with my c6509 switch. File attached for ref.
Hi every bodyhow is every one doing ?I configured a virtual link between R1 and R3 ; area 1 is transit area. area 0--R1---area 1 ----R3-- area 0Even when i removed the virtual-link between the two by using" no area 1 virtual-link 1.1.1.1 ,no...
I'm working on a customer's network and have two 5k's setup for redundancy via HSRP. We are having an issue testing the VoIP vlan (vlan 110) failover. When we test failover on VoIP phones (Siemens VoIP system) we go through the following steps: 1. O...
Hello Friends,One of my clients requires Wireless Networking to be done in his Supermarket, The area of his Supermarket is 2300 feets x 2 (Ground Floor & Upper Floor). My client wants to use PDT Devices so that his employees can remain connected to t...
Dear Community,with regards to my recent post 'https://supportforums.cisco.com/thread/2116099?tstart=30' Proxying traffic through VPN/GRE tunnel,I found the feature to use 'ip next hop recursive' inside a route-map declaration.Cisco explains this fe...
Hello,If I have two stackable switches one switch uplinks to one 6509 core switch and the other connection uplinks to another 6509 core switch, and also the other stackable switch does not connect to the core switches. Because I am using hsrp and als...
hello guys....I have a very simple query please help me to find out:I have only one IP series 192.168.1.0/24and there are 4 Routers, 8 Switchs and 8 PCs which need to configured, in each Router there will be 2 Switchs with two FastEthernet port has ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |