I have encountered a strange issue with my 3560G switch running c3560-ipservicesk9-mz.150-2.SE10a.bin. It will ping the gateway and other computers for a short time then refuse to ping anymore. The only way to get ICMP replies is to move the crossove...
is the FL-44-SEC-K9 needed when purchasing the FL-44-HSEC-K9?
I am trying to hit network with a 172.21.29.x (external network). I can't ping, when I run a traceroute i get the following9300#traceroute 172.21.x.xType escape sequence to abort.Tracing the route to 172.21.x.xVRF info: (vrf in name/id, vrf out name/...
Could anyone share guide to capture interface packet in and out in n9klike monitor capturusing ethanalyzer
Hi FolksReaching out to experts in the community to see if anybody has any ideas or, has perhaps come across this issue and knows of a quick fix. Technically, I've spent hours researching this, and tried a bunch of things, but nada so at this point, ...
Hi I have a 9300 switch where I had some issues with a 9300 switch that got fixed by a restart. I am now looking into the tracefiles to see if I can find anything interesting. In the old days Cisco had a tool to analyze tracefiles and crashinfo files...
Hello, I have a catalyst 9300 that I wish to factory reset. I interrupted boot from flash and got to the "switch:" prompt. I tried to type in commands but couldn't.. The only key that the switch reacted to until now is ctrl+pause (which entered a new...
I work in a factory that has 100's of machines that all run identical programs. I would like to connect them to a network so I can access them remotely and also collect data. Trouble is all of the machines have the same IP address because they are ...
Please help, because when I executed the command "show platform resources" I noticed that the DRAM QFP shows a critical status with 97% of use. What is the reason for this usage, could it be a memory leak? Greetings.
we have two switches in VSS mode, may i know the command to show the configuration of vss, thanks
I have cisco 8300 router and would like to have two T1/E1 for redundancy. How do configure the router to switch amongst them in case one of the T1 links fail?
Having an issue on a 3750 stack where we've enabled Jumbo frames for the gigabit interfaces and now I want to configure a WLC5508 to etherchannel to the 3750. I've gone through and created the Port-Channel interface but I when I add the member Gigab...
Setting up a new C1000 switch so I wanted to know if I need to remove the vlan and just have it as a trunk port. Thanks,
Hi Experts,I would like to check, would it be possible for us to connect 2 ISPs(Point-Point or WAN) to CISCO 2960-X for 2 systems?. Attached sample network diagram. Please advise.Much appreciated in advance.Regards,draj
I have a question on when to use private VLAN trunking. I have read when trunking to a device that is not PVLAN aware, you should use PVLAN trunking. If you are trunking between devices that are PVLAN aware the you should use regular trunking.What ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 05-14-2025 09:31 AM | ||
| 05-06-2025 02:02 AM | ||
| 04-23-2025 06:26 AM | ||
| 04-23-2025 06:18 AM | ||
| 04-19-2025 09:40 AM |
| User | Count |
|---|---|
| 8 | |
| 6 | |
| 5 | |
| 4 | |
| 2 |
