Switching

Hi All,What does mean by invalid boot string, how can i set the correct boot string.6513-01#show diagnostic sanityPinging default gateway 192.168.30.1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 192.168.30.1, timeout is 2 seconds:!...

Hi,I have some 10 servers which is runing multicast applications. Now I would like know those Multicast IP address of those servers.Is there any command to check the same in router.Regardssateesh

Hello,We run a dedicated server business. \We assign ONE VLAN per customer with a 8 IP subnet (5 Usable) for the primary IP of the server + 4 IP's the customer can use.When assigning additional IP's to our dedicated server customers... which one of t...

I have two 6509 switch connected via a fiber trunk on the SUP blade.All vlans are trunked on this trunk.Both switches have monitor sessions set up on them and I am getting an error trying to create an additional one.I am thinking I can remove one of ...

A vendor has requested that I enable multicasting. The video will be broadcasted over a flat network/one subnet. Network consist of a meto-e terminated in a 4503 with 12 2960s. As long as they are sending the multicast traffic to 224.0.0.1, will i...

Hi, I just upgraded the IOS on dual Sup720's in a 6509 chassis. I FTP'd the new IOS on both fine, updated the Boot system to load the new IOS. Reloaded switch and all seemed to work ok.However, every time I do a wr mem I get the following error mes...

Hi All,We are in the process of upgrading our network infrastructure. We are planning to invest on 2X 6500 core switches, so I thought of proposing VSS to the management as the best solution. I have few questions that need to be clarified before that...

I deleted the IOS on a 3750, now I need to use xcopy to reinstall a IOS. I will be loading c3750-ipservicesk9-mz.122-35.SE5.binWhen I put in the following command:switch: copy xmodem: flash:c3750-ipservicesk9-mz.122-35.SE5.binI get the following res...

Hi all, if I have 2 routers, 1 pri and the other secondary, if the primary fails and r2 becomes active, if the primary comes back, will it not fail back to the primary unless I use the preempt keyword? do I need to configure this on both or only 1 ro...

Is possible to change precedence of packets arriving to 2960s portI did following configuration access-list 110 permit ip any any(just for test all ip is permitted)class-map TESTmatch access-group 110policy-map TESTclass TESTset precedence 5interfac...

HiI'm new to multicasting so I'm confused about the following. When I run "Show ip mroute" I get the following:(10.45.8.34, 239.255.3.20), 11:28:59/00:02:53, flags: TA Incoming interface: Vlan8, RPF nbr 0.0.0.0, RPF-MFD Outgoing interface list: ...

Hello Experts,I am trying to use two DSL ISPs to share my VOIP traffic of about 19 SIP phones using G711. I am thinking about using one 2811 router with three Fa interfaces. One interface will go to ISPA, second will go to ISPB and third will go to L...

Hi.I have a network connected to two Switches, and each Switch connected to the same two Routers. Those are the gateway to the outside. There isn't any routing protocol configured in the routers, only static routes. The interface of the routers conne...

All,I don't think this is possible without extra equipment/software, but I wanted to ask.Is there a way that I can create a time-based ACL and apply that policy-map to the ACL (or vice-versa)?What I want to do is restrict flash applications between 5...