Is there any negative impact of enabling flow control on a 3750? I noticed that it only supports inbound packets.Thanks!John
Is there any negative impact of enabling flow control on a 3750? I noticed that it only supports inbound packets.Thanks!John
Hi guys, I am new and fresh in using Cisco product. I am about to start Cisco class I need your advice in wish Cisco router is good for me as a fresher to practice on so that i can achieve my CCNA.Regards,Tona
I want to setup a CUCM lab environment on a seperate vlan but want to take advantage of the POE ports on my 6509. Is there an easy way to create a new vlan but not have it be automatically routed. I don't want any possiblity of the lab CUCM interferi...
Hi,I have 2 Catalyst 6500 working as VSS.After making an upgrade of IOS (current: s72033-ipservicesk9_wan-mz.122-33.SXI.bin) gives the following error message:SW1_SP: Insertion of mld_s_g_type in the tree failed WAVL grpI searched information about t...
I have a 3750 at a remote location. I have it connected to an Avocent console server, so I can access it via the console. It currently has no image on it and only loads to the boot loader. I know that typically I could load an image through xmodem...
Hi,I have an existing switch stack of 3 cisco 3570s. I need to add a new switch to the stack. Is any configuration on this new switch necessary, or can i just connect it to the stack and it will pick up the config from the current established switche...
can some one provide me a document that cisco 6509 switch is a approved MPLS FORUM device
if an IP address or computer is communicating with another and you see e.g 192.168.246.23.134 > 192.168.246.128.134: udp lenght 50, please how can this be interpreted and what does ">" mean?
I need to upgrade my SUP720's IOS, but can't find what version FPD my SPA needs for the new IOS version. Is there a chart somewhere? The "Hardware/Software Compatibility" tool isn't helping.Thanks,Bob
Dear all,I am facing issue on setting up the port-channel between ASR1004 and a switch. I have to configure "port-channel load-balancing vlan-manual" command to bring the channel up. But by doing that, the port-channel become active & standby mode wh...
Hello,I just want to know how ip helper-address work when we have multiple DHCP server for redundancy. If we configure ip helper-address command twice with two different DHCP server, How does it going to relay the DHCP request message ? I appreciate ...
We are adding a small office (28 users) to our network. They are on a different floor and will connect to the backbone via fiber. Could a SRW2048 switch be used? When would I need to go with something like a 2960g-48-tc-l instead? Big price differenc...
I currently have VTP running on my network. The network is composed of 2 6509's running CatOS running ver 6.3 and various 3550 and 3750 switches. The 6509's as the servers and all other switches as clients.I'd like to remove VTP from the network are ...
HiI have a interface with 200 sub interfaces, each with its own standby munber.Is there anny problems with a sub interface having the same standby id,or is it possible to run HSPP ver 2 on a cisco 7600 router ?The router is running Version 12.2(18)S...
I inherited a network and see some odd configurations that I don't normally do and can't think of a reason for it. One of them has the following statementsspanning-tree uplinkfastno spanning-tree vlan 20no spanning-tree vlan 27no spanning-tree vlan 9...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-25-2024 03:21 AM | ||
10-24-2024 11:57 PM | ||
10-23-2024 06:42 AM | ||
10-23-2024 01:37 AM | ||
10-15-2024 03:13 AM |
User | Count |
---|---|
14 | |
9 | |
8 | |
6 | |
5 |