I have a switch that connects to a 2800's f/e port. The switches port is configured to trunk only vlan 2. There is also an SVI on the switch for vlan 2. However, the router port only does layer 3 and the SVI needs to be routed across the WAN. How...
<p>I created an EtherChannel group 1. I can see both interfaces with the "show etherchannel 1 summary" but both interfaces appear with a (D) instead of (P). I have the same configuration on both switches. I am using ports Fa 0/1 and 0/8. Any hint to ...
I tried to configure community PVLAN on a sup6 for catalyst 4506E.In the configuration guide I found the following:Supervisor Engine 6-E does not support community PVLAN and community PVLAN trunk ports. Why is it so? Is there an alternative available...
Hi all, can u help me for the required commands in finding the following modulesMEM-MSFC2-512MB MEM-XCEF720-512MB Anand
I have two equal paths between my data center and disaster recovery site. They are both 100 mbs metro-ethernet connections. Due to limitation on the carrier's equipment I'm running layer 3 between the sites and not layer 2. Basically the carrier can'...
hi, please advicei need to configure 4900M switch with combination WS-X4920-GB-RJ45 + WS-X4908-10GE cards and i need to use 2x10GE onboard port + 15x1GE copper ports + 6x1GE SFP optic ports (via 3 twingig converters plug into X4908-10GE card).Do you ...
Hi,I have set up a RIPv2 lab with 3 routers, and wondered how easy it would be to move over to OSPF? I'm notsure how long a task like this should take.
can you please share some document on desugn & configuration of vrf on cisco 6509.
Hi I need basic configs for CAR between two routers connected on a serial cable point to point.
Hi all, can anyone tell me when using pvst on switches, where does the vlan info for each spanning tree instance get carried?
We are trying to configure VSS with two 6509 switches. The accsess(4507) is connteced to the vss(6509) distribution using MEC.The port channel in the vss is not coming up. Following are the configurations on both switches.in 6509 VSS###########int po...
I have a catalyst 3548xl with a 1000BASE-SX gbic module and I want to replace a failing dell Powerconnect. The problem is I am unable to connect the 3548 to the other dell with the fiber. The connection stays down and come up for a second when the de...
Dear All,I am planning to configure on my two 6506E with Supervisor32 an Etherchannel, it will be composed by tree ports from the primary supervisor an tree from the redundant one, for each 6506Es.My dubt is about what type of etherchannel is better ...
Hi All,We have the attached architecture(2 C6513 with several C3560 on floors) and as the customer needs to implement Alcatel Voip platform with Qos over the LAN, I want to know wich config I need.I generated autoqos voip trust (Ip phones tag with DS...
Hi, I would like to stop BOOTP service on Cisco 3750 Switch running IOS Version 12.2(25)SEE4.Please share the commands.I am unable to run "no ip bootp server"regardsNeo
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-23-2025 01:45 PM | ||
| 07-08-2025 11:44 PM | ||
| 07-04-2025 02:13 AM | ||
| 06-26-2025 10:05 AM | ||
| 06-16-2025 07:47 PM |
| User | Count |
|---|---|
| 13 | |
| 11 | |
| 9 | |
| 5 | |
| 4 |
