Hi,we have internet line from bharti and we want to terminate on layer 3 switch.what configertation will need to be done.
Hi,we have internet line from bharti and we want to terminate on layer 3 switch.what configertation will need to be done.
Hi all, suppose i have 10 neighbours configured in bgp process of RA, now i want to advertise network 25.0.0.0/8 to only neighbour 12.0.0.1 in the same AS, i want to do it using the minimal set of commands, how can i do that ?? i dont want to adverti...
Hi NetPro,just to confirme with the DHCP configuration is that correct. thanks.Core-Switch-----------interface Vlan312 description Vlan ip address x.x.x.x 255.255.255.0 ip helper-address x.x.x.x no ip igmp snooping explicit-tracking ip ospf message-...
Hello,I want to ask if there is a possibility to create manual or automatic (configuration ) traps on a 6509/6513. The questions is regarding to Network Monitoring with NNM and OVO. Need to see if manual generated traps are being showed up on these t...
Hi!What I do like to load, with a command line only, a configuration stored on an ftp server or tftp. What my advice? We need to know because I am developing an application that will allow me to load jsp through commands rcp rsh or any configuration ...
Hi @ allI think,it is a easy question.Is it possible to start a reverse telnet session over the aux port from a Cisco 2821 Router to a Console Port from a Non-Cisco Device (for Example a Lantronix Console Server)???If yes, which parameters are necess...
What is the main difference between L2 & L3 switches ? Can somebody point me to a link that would describe the differences between the two.
Hi all,Yesterday I did an IOS upgrade on Sup720. I pointed the bootvar to the Sup-bootflash and Sup720 went into Rmon mode. Once I pointed the bootvar to the Sup-bootdisk, it worked.After doing some research, it seems like Sup-bootflash and Sup-boo...
I have following configurations in one router and i am not been able to fetch the details thay y are they used. kindly suggest me some link or info regarding this rtr 1 type echo protocol ipicmpecho 192.168.52.34!rtr schedule 1 life forever start-tim...
I have a 2621 router installed and I want to restrict certain production computers from accessing anything other than the subnet they are on. What is the best to way to do this with a 2621 router? I was thinking an ACL but I figured I would post just...
Is it possible to run an LACP etherchannel with a PAGP etherchannel on the same switch?I have a HP switches on a blade server which only support LACP and my current environment only uses PAGP. I am testing this on a 3x 2970 with 12.2 IOS in a mesh.
hi allis it possible to filter say 7-8 different ip address by creating a group and apply that group acl. eg.if i have 10.5.5.10,172.16.10.10,192.168.20.20,192.168.10.10 etc, rather than creat individual permit/deny acl can i not just group the abov...
We are getting ready for a voip implementation and have our data vlan and voice vlan created. We go from a stack of 6 switches via fiber module to location in plant to a 3560ps works great there, but I need to setup a temp switch (poe) in training r...
How do you reconfig an etherchannel from trunk mode on to desirable? have 2 6509's with an active etherchannel config'd using sup720 ports 5/1,5/2 and 6/1, 6/2. slot six is redundant card on both mls'.
I'm searching for a solution to realise link aggregation with a VMWare ESX Server and three Cisco Catalyst Switches.The ESX Server has three NICs. NIC1 should connect with Switch1, NIC2 with Switch2 and NIC3 with Switch3. All three Switches have an i...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |