Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

my server folks want their ftp serverto use a specific route...this is the only device they want to use this pathif the ftp server on the far end is192.168.5.6 255.255.255.0would my static route be192.168.5.6 255.255.255.255 192.168.4.3If 4.3 is the ...

Hi There;I have a switch with 5 vlans (192.168.1-5.X/24), connected to a router which has three interfaces (172.30.1-3.X/24)in addition to the uplink port. If I want the traffic from each of the 5 vlans to be able to talk (ping)to each of the 3 rout...

austindaz by Level 1
  • 457 Views
  • 6 replies
  • 0 Helpful votes

Hi,a few days ago I updated my 2950 from IOS 120-5.3.WC.1 to 12.1-22-EA11.Since then my infrastucture started to behave in bizarre way. The leds suddenly stop blinking and after a few seconds recover their normal status.The switches are connected thr...

julupegon by Level 1
  • 370 Views
  • 3 replies
  • 0 Helpful votes

I have a pretty good idea what the answer will be, but here goes...is there a way to obtain IOS updates on non contract Cisco routers? We have a bunch of 2651's that Verizon had installed way back when and I'm looking to upgrade. Thanks.

We will be replacing one of our 24 port switches with a 48 port one. Is there a way for me to import the old settings and tweak them? Or will I have to reconfigure all the settings on the new switch? I have never set one of these up before. So plea...

DonnaJ by Level 1
  • 570 Views
  • 7 replies
  • 0 Helpful votes

Hi, I have a 6509 switch with the Sup720 and a fwsm. I cannot get these two modules to communicate. When I ping the fwsm from the sup720 I get no response, and when I ping the sup720 from the fwsm I get no response. This is my first experience with t...

amadeusri by Level 1
  • 990 Views
  • 7 replies
  • 0 Helpful votes

Hi, we have 2 weblogic web servers clustering and fronted by our CSS and it seems to work pretty well. However, when the one of the two web services fails the existing client connection to this failed service is reset and a NEW client connection is ...

I want to prevent my border routers from responding to pings and traceroutes from outside addresses yet pass ICMP packets if I'm pinging from my internal addresses. If I apply this ACL to my interface will it do what I need:access-list 120 deny icmp ...

Hi,Can someone explain me in detail how the STP decides on the location of the blocking port in a square/circle of switches?I have attached a real life example. Why is it blocking on the indicated port on that segment and not on the segment between t...

I've been getting disconnected from My collo, and wondering if this error is the problem, "*Feb 26 17:00:16.083: %GT96K_FE-5-LATECOLL: Late Collision on int FastEthernet0/0" I know a collision can't be that bad, but can too many of them bring down m...

Hi,I have a very simple NTP config that consists of these commands:ntp source vlan 210ntp update-calendarntp server xxx.xxx.234.10 preferntp server xxx.xxx.234.12The clock remains unsynchronized. Host xxx.xxx.234.10 is a firewall that gets its time ...

riverar by Level 1
  • 2805 Views
  • 1 replies
  • 0 Helpful votes

Hello,I have a 6509, Sup720's running 12.2-18.SXD7b.We PXE boot a large number of machines.We have DHCP leases set for 5 minutes. The low lease time is due to items being swapped out for sparing purposes.They cannot use the next IP address in the sc...

Today I was totally flustered and confused when I saw the state of my switched network. I'm administering a military network with approx 50 users; we run W2K3 server with DNS, AD, and Exchange local to our subnet. We draw services from a fiber pedest...