Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi, in my network i want to make sure that every router has exactly 1 route to other routers LAN ( there are total of 100 routers in my network ), is there any way to do it ?Thanks

Hi AllI was thinking of picking up a Cisco 877W router to act as my wireless modem/router. However my ISP will not support Cisco though they have provided a basic configuration to get the ADSL up and running. I am not sure I understand the configurat...

keeleym by Level 5
  • 924 Views
  • 4 replies
  • 0 Helpful votes

Three questions:=================1) We do not have any parts and I wish to make sure that we get the right parts. Problem: When we turn ON the 7604 router the STATUS LED on SUP32 stays RED and the FAN TRAY LED stays RED. When we unplug the fan tray w...

I have a DS3 plugged into our 4510R Cisco Switch that is shutting down for now apparent reason... i use the CNA client, and the only issue i see is when i look at the Graph\dropped packets and errors, is see 8mil errors... i ran an analyser to view t...

davisr651 by Level 1
  • 371 Views
  • 2 replies
  • 0 Helpful votes

Hello FriendI am currently struggling with RSTP, can anybody give me good referance documents links or so-V

i am getting this error on my L3 switch'Host 02:01:00:00:00:00 in vlan 1 is flapping between port Gi2/14 and port Gi2/7'how to solve this problem? why it happens?Thanx in advanceBava

bava_ccna by Level 1
  • 354 Views
  • 3 replies
  • 0 Helpful votes

Hi all, i work in a bank (IT WAN), we were thinking that is there any benefit in shifting to IPv6 ? right now i am quite sure that IPv6 is not supported by ISPs, so what might be the benefits of deploying IPv6 in our environment in order to convince ...

Hi,I am looking for solution to analyze, monitor, troubleshooting and find out issues at data traffic flow like loss connection, packet retransmission on Cisco Switch 6500 at LAN. I have already seen suggestion to enable Netflow feature with a NetFlo...

glaucio by Level 1
  • 470 Views
  • 4 replies
  • 0 Helpful votes

I'm attempting to add a 48-port ws-c3750-ts as a slave to an existing 24-port ws-c3750-ts. I provisioned the 48-port 3750 offline with the 'switch 2 provision' commands and set the priority to 13(master is set to 15). After I reloaded the 48 port 37...

I'm setting up an AP350 access point which is connected to a 1721 router and a 1548 switch.The 1721 is set with a static IP address of 192.168.0.2 which the AP350 uses.The wireless interface of the AP350 is configured to give out ip addresses through...

rjdavison by Level 1
  • 540 Views
  • 1 replies
  • 0 Helpful votes

Hi There;I'm looking for an example interface script for an asynchronous RS422 serial connection from a 2811(DTE) to a modem(DCE). How do I route the traffic to the modem? For instance, am I required to give the modem an ip address to act as the ne...

austindaz by Level 1
  • 590 Views
  • 1 replies
  • 0 Helpful votes

Hi,I've tried to create an access-list on one of our remote sites to block access to everything but a Citrix Server and External DNS.*Config*int fa0/1ip address 10.0.104.254 255.255.255.0ip access-group 101 inexitip access-list ext 101 permit ip 10.0...

I am in the process of upgrading our hybrid 6509's to new VS-S720-10G-3C sups 4000W PS's and Highspeed fantry. I replaced the power today and that went well. My questions for the group are:1- Can I replace the fantray with the system online?2- Ca...