TelePresence and Video Infrastructure

Resolved! SIP Provider Intergration

Hi Guys I would like to intergrate cisco router to a sip provider for cut down on costs. How can I get the router to register to sip Provider and with various parameters such as username, password etc... and which is the Best entrance level router th...

Resolved! Legacy PBX Intergration

Hi guys Current setup Alcatel Omni Pcx Office PBX ( with analog interface rj11) --------------.> PSTN Required setup Alcatel Omni Pcx Office PBX ( With analog interface) rj11-------------> Cisco router ---------------------------> VOIP As can be seen...

Resolved! VCS Expressway Private IP Address

I have a VCS Control and Express that seem to work properly with normal endpoints. Also, Movi users can register from inside to the control without a problem.I have the zones,etc. setup properly I believe.What I am not sure about isControl and Expres...

VCS Expressway Starter Pack System Name

We are trying to configure the VCS Expressway Starter Pack. What is the diffrence between the System name and the Cluster name? Can they be the same?

Directory on midlet not showing listings

Having recently upgraded from Call Manager ver 7.1.3 to 8.6.2.200 on Cisco's recomendations we are now encountering an issue with the phone milet and its ability to see the directory listing. this was working ok prior to the upgrade. Prior to the upg...

Resolved! CTS 3210 Firmware Downgrade

Good day,we were asked to upgrade a customer's CTS 3210 firmware from 1.6.7 to 1.7.6. They are also running CUCM 7.0.2 The customer advised that this was to enable proper polycom interpoerability and we went ahead and installed the file on the TFTP s...

Resolved! difference between voice gateways and gatekeeper

Hi,Could someone kindly explain (or provide a url link) the main difference between voice gateways and a gatekeepers ?Regards

Not able to find CTMS 1.8 software on cisco.com

As far as i know, CTMS 1.8 is released but the latest version available for downlaod for CTMS is 1.7.3 on cisco.comCan someone confirm?Regards,Anjali

CTS1300 bandwidth

Hello,Is there a document that outlines the bandwidth requirements for a CTS1300-65 with CTS version 1.9. I had seen a document which gives an idea for versions 1.3,1.4 but I was looking for a more recent document.Thanks in advance.

Calls from register to unregestred endpoint giving error code no.6 on local-endpoint.

HI Team, I am having VCS-C at one of the client-location, Whenever I am dialing a call from register endpoint to un-register endpoint (located remotely) , I am getting an error code no.6 (i.e Unacceptable channel) error on my local TANDBERG ENdoint.V...

Tandberg licensing system down?

I am trying to upgrade a C40 and when I enter the Serial Number and MAC of the C40 and click on the Verify button on the licensing page, I get this error:Error in fetching Contract details as the C3 Connection is not available.. I assume this is a Ci...

Resolved! C40 Multisite call

Hello all,I have to configure Multisite/multiway,We have VCSc and MCU.and endpoints as C40's,ex90 and MXP1700.Ex90 has Multisite license, but for C40 its not. Iam able to do P2P Calls and then adding other endpoints to the existing call from EX90.We ...

Resolved! VCS-C allow direct IP address with VCS-E also

Hi,I have a VCS-C with a VCS-E in an environment x7.0A majority of endpoints are registered to the VCS-C but there are some endpoints that cannot for specific reasons.The endpoints that are not registered to the VCS-C can call registered endpoints by...

EX90 booting problem

Hi,The EX90 is not booting up. So I can not reach it. Is it possible to do factory reset with any button or something on EX90?Best regards,

VCS-C not showing all registrations?

I'm searching through the VCS-C registration history for a scheduled conference held on my MCU this morning. The VCS-Control event logs show the registration, so why doesn't it show up in registration history?

TelePresence and Video Infrastructure

Forum Posts

Resolved! SIP Provider Intergration

Resolved! Legacy PBX Intergration

Resolved! VCS Expressway Private IP Address

VCS Expressway Starter Pack System Name

Directory on midlet not showing listings

Resolved! CTS 3210 Firmware Downgrade

Resolved! difference between voice gateways and gatekeeper

Not able to find CTMS 1.8 software on cisco.com

CTS1300 bandwidth

Calls from register to unregestred endpoint giving error code no.6 on local-endpoint.

Tandberg licensing system down?

Resolved! C40 Multisite call

Resolved! VCS-C allow direct IP address with VCS-E also

EX90 booting problem

VCS-C not showing all registrations?

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

Touch 10 boot looping on RoomOS 11.15 with IPv6 DNS server address

Codec plus and HDMI passthrough / Call from laptop

Cisco precision 60 camera direct connect to laptop

RoomKit EQ lack of HDMI audio

Cisco Navigator pannel didnot connect to the network

CMS upgrade from version 2.8 to 3.3.2

TMS Update

Roomkit EQ codec SIP or H323 dailing not working - Dial command failed

IP Direct Call Error with Roomkit EQ

Trouble loading Room OS11 to Webex RK Plus