error: Login error: Authentication failed, we have configured ldap. the same configuration work on ucs central. UCS central 2.0(1d) and UCS manager 3.2(2f)
Has anyone had success booting a B200M4 with UEFI and Windows 2012R2? We are able to install the OS without issue but once the install has completed and the server reboots we get a BSOD stating that the ntoskrnl.exe is missing or corrupt. I mounted...
Hi,I would appreciate quick response as this is in production environment.currently we’ve 3X UCS 5108 chases configured in HA with full blades mix (B200 M2, B230 M1) using two 6296 UCS Fabric interconnect connected to two Cisco MDS 9148 SAN Switch wi...
Team,I was wondering how I might run a basic web page that would pass parameters to a cisco ucs powershell script (cisco powertool).Does anyone know how this might be accomplished and would you provide a sample code?I would assume I would need to run...
hi friends
i am implementing a cisco UCS environment and in networking step i have encountered a problem, steps which i have done are these:
configuring a port channel between FI and northbound switch that works properly and it's status is OK (port c...
I have search to no avail to find a way to use powertools to remote connect to a C-240 M4 and change the Password from default to my selection without plugging into the physical server and manually making the change. Note I need to use the managemen...
Hello,
Currently we’ve 3X UCS 5108 chases configured in HA with full blades mix (B200 M2, B230 M1) using two 6296 UCS Fabric interconnect connected to two Cisco MDS 9148 SAN Switch (VSAN #2) with one EMC VNX2 storage. (diagram attached is similar t...
So...I need to upgrade two 5108 Chassis / B200 M2 and I have some doubts.1st- Which version should I use? I took a look at the https://ucshcltool.cloudapps.cisco.com/public/ but I am not sure abou it. 2nd- How to performe the upgrade, I mean ... I kn...
Hi,
ESXi is installed on a blade with a service profile that has no vHBAs.
If the vHBAs are added to the service profile, does ESXi need to be re-installed when that service profile is re-applied to the blade?
Thank you,
Does anyone know if the ports in the Expansion Module for the 6248UP (pn UCS-FI-E16UP=) can be used for same personality types as the fixed ports? We need ports for the uplink to the core and downlink to the chassis. We are receiving differing infor...
Hi
I am new to Cisco UCS product. we have bought a Cisco UCS 5108 with 4 blades and 2 FIs. now i am implementing it.
Cabling is finished and i have all connectivities established to storage and network.
now i am going to create a service profile and ...
Hello All,
I have a Cisco UCE-E 140D and a ISR4351, however, I am trying to configure the uc1/0/0 and uc1/0/1 for trunking through the subinterfaces of the router. I am running vmware 6.5. For example , I have subinterface on the router gi0/0/1.90...
Hi Guys,
Need some help with UCS central backup job. I have created one time backup job for a ucs domain. Now i am trying to figure it out how to delete that backup job, but could not find it. This backup failure keeps on alerting a major alert. ...
Hi,
I'm getting this Minor fault on my primary FI :
Disk usage for partition bootflash on fabric interconnect A exceeded 70%
Wanted to know, what can I delete from it, except .bin files.
Is there some "garbage" files that I can delete from it ?
t...
All,
Is there a method for converting an existing single card flex flash to RAID 1 without losing data on the existing flexflash card.
Blades were originally purchased and configured with a single FlexFlash SD card. Now there is a desire to add ...
