Hi all, Attempting to connect two new C240-M5 (with VIC 1457 MLOM) to existing UCS. M5s are connected in dual wire to redundant/HA FEX (one uplink to each FEX). We are using port 1 and 3 on the VIC to connect up to FEX. UCS / FI 6454 are running 4...
Forum Posts
I currently have 3 chassis fully connected and in production. We maxed out on blade slots so I added a 4th chassis. I configured each new port on the FIs (6332) for server traffic and cabled the chassis. Chassis went through discovery process but Im ...
Hi team, I would like to knwo if the new chassis and blades serie X can be manage using fabrics 6400 with UCSM Managed Mode (UMM)? This new X series chassis blades will replace the actual B-series chassis/blades? Thanks,
We currently have a domain running 4.1(3h) that has the default host firmware package changed to a version that is not supported by the M5 blade proc's. This is causing us an issue where we cannot associate Global Service Profiles from a Global Temp...
Resolved! hyperflex storage controller
i trying to configure hyperflex cluster using the profile in intersight.com (it's the first time for me).there is to configure "storage controller ip", i insered an ip casually because i haven't it and also i haven't the storage controller VM.where c...
Hello,I have a Cisco UCS C220 M5SX and in the CIMC the embedded 1/10G NICs are not detected. The same is also on VMWare ESXi 7.03 Cisco Image.I have also added an i350 MLOM Card and the Card were only detected, if I set in the BIOS the Option "All On...
Have (3) HX220SX M5 Edge servers with Cisco 12G Modular SAS HBA RAID controllers and Nexus 9K switches. Trying to install and run Hyperflex using Windows Server 2019 and Hyper-V but it appears that only vmWare installations can be done without Fabri...
Dear all, I have a C240M5SX updated with the latest Cisco UCS Host Upgrade Utility (ucs-c240m5-huu-4.1.3f) and I face two issues : sometimes when a try to map an iso as a virtual media, I can't because the vKVM gives me the message that another user ...
I just received 2 new servers, when tried to configure the CIMC parameters it prompts for the current password and to change it, I tried the default "password" and also read something on internet about Cisco sent some servers with default set to "Cis...
I got new Cisco Standalone UCSC-C240-M5SX (with GPU) installed and configured.However, Windows Server 2019 detected an “Marvell Storage Controller” which we have challenge to install driver. Product Name: Cisco Boot Optimized M.2 Raid Controller Sl...
Hi all, I am planning to upgrade cucm 11.0 to 12.5, current esxi version is 5.5 and it is not compatible with cucm 12.5. In order to upgrade from esxi 5.5 to 6.7 license key upgradation is mandatory. Can anyone suggest how to upgrade the esxi license...
Peoples, We had a problem with a HX node and I needed to re-install ESXi on and and now I am trying add the node to the HX cluster (two nodes are in place today and am trying to re-add the third). I keep running into this error. Installing Software...
My client bought 2 new b200 m5 blades to put into empty slots of their 5108 chassis.Their FIs are 6248UP with their infrastructure firmware at 3.2.3lBlades would not pass discovery. TAC support stated that we need to upgrade their infra firmware. (3....
Good day.Maybe not in this topic. We have UCS Mini 5108. The scheme of connection such - the switch cisco --> UCS --> ESXi.On one blade, you need to install ESXi with several vlans on one interface and broadcast to vSwitch ESXi. We set up a service p...
Hello Folks We have a relatively older system running UCS B200 M3 on 5108-AC chassis in a very large installation over 35 Blades running. We were looking to replace some of the blade servers with M4 or M5 and can't seem to get any straight answers. T...
