Voice over IP

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Forum Posts

I have a remote office w/ 2 local analog lines that have a 2620 router setup in SRST mode w/ a VIC-2FXO-M1Everything works fine, expect Caller ID. I am using MGCP - not sure if that is a problem or not.Here is my port config and the router debug info...

IOS:c2950-i6q4l2-mz.121-22.EA1.binConfiguration:interface FastEthernet0/2 description IP Phones&PCs switchport mode access switchport voice vlan 200 mls qos trust device cisco-phone mls qos trust cos no snmp trap link-status auto qos voip cisco-phone...

tony.h by Beginner
  • 592 Views
  • 6 replies
  • 0 Helpful votes

IP phone works good in main location. At Remote location, able to call to and from but not able to here voice. Phone system is plugged into port on Cisco Catalyst 2950. Any suggestions?

i have configurate the application offramp on a cisco 2651XM but when i test it comes this error: UTC: //99/512F553A8033/MSPI/mspi_bridge: Either Source Interface or Destination Interface is CC_IF_TELEPHONYthe call at the fax star and when it answe...

hi,Pls can someone assist me with now I can send ANI to a PTO Switch connected via PRI E1s. The 5th and 6th digits must be alternated in every call sent to the switch.Cheers,Kay

olakayode by Beginner
  • 301 Views
  • 3 replies
  • 0 Helpful votes

Dear Netpros,We are having a 4E1 Cisco AS5350 Voice Gateway. Now when we run the command "sh spe voi summ" we see a lot of Payload Type Violation and Buffer Overflow errors as shown in the Output below. Any clue as to what is the source of these erro...

rushabhns by Beginner
  • 366 Views
  • 1 replies
  • 0 Helpful votes

Hello NetPros,We are having a 4E1 Cisco AS5350 in one of our POPs. Now when we run the command "sh voice trace 3/2:1" on our gateway we see a series of error message like "9004056.768 (S_CONNECT, E_DSP_PROTOCOL_ERROR) ->". Does anyone know the cause ...

rushabhns by Beginner
  • 331 Views
  • 1 replies
  • 0 Helpful votes

Hi all,Does voip hair-pinning supported by Cisco gateways?I mean, can incoming voip call leg be connected to outgoing voip call leg on the same gateway?Thanks,Mike

kozharov by Beginner
  • 480 Views
  • 2 replies
  • 0 Helpful votes

Is it possible If I have dial-peer voice X voip for inbound to route this call to dial-peer Y voip for outbound.I tried to implement this, but every outbound call go via dial-peer pots.Any ideas.

k_petkov by Beginner
  • 367 Views
  • 2 replies
  • 0 Helpful votes

Hi Prompt please how to receive event NOTIFY in a TCL script?ThanksJan 18 01:14:05.277: ISDN Se3/0:15 Q931: RX <- NOTIFY pd = 8 callref = 0xACBC Notification Ind i = 0xF9 Display i = 'REMOTE HOLD 'Jan 18 01:14:09.671: ISDN Se3/0:15 Q...

angel-ok by Beginner
  • 434 Views
  • 0 replies
  • 0 Helpful votes

Hi,Does anybody know how to append an extra digit to the least significant part of a called number on a range of DDI numbers.i.e dialled number 67xx to be expanded to 67xx0or 6750 expanded to 67500ThanksTony

thack by Beginner
  • 556 Views
  • 5 replies
  • 0 Helpful votes

I'm trying to configure our cisco gw for voip (debit card appl.)I've configured our call application as below:call application voice best tftp://xxx.xx.xx.xx/tcl/app_debitcard.2.0.0.tclcall application voice best uid-len 4call application voice best ...

yavuz2003 by Beginner
  • 336 Views
  • 1 replies
  • 0 Helpful votes