Voice Systems and Accessories - Small Business

Hi I need to setup an alternative proxy in the spa5xx phones. Our phones are running 7.x version SW and I saw the alternative option on the web page of the phone but now can not locate it as it only shows the single proxy option. Is there an option I...

We have a set of uc520 , ios version :uc500-advipservicesk9-mz.151-4.M6 , there are few 7960 phones working well . When I new add one 7960 , It shows 'protocol application invaild ' . I found the page http://www.cisco.com/c/en/us/support/docs/voice-u...

How can I turn off the speaker for a spa509g phone? We have the Plantronic wireless headsets w/lifter. Just turning the down the volume also turns the volume down in the headset. 

I have been trying to connect a SPA525G2 to one UC540 and I have not been able to find any information with the clear steps to do it.I have an IP Telephone SPAS525G2 and I need connect it to a UC540 for a remote connectivity using the VPN SSL client ...

Hello, have a uc540 running 8.62. Have an extension when it's in use, doesn't light the blf on other users phones. IE ext 110 picks up the phone and is in a call. Rest of users on system with a watch mapped to the ext 110 DN, don't see the ext ...

Hello, i have to configure the unit keys of a SPA514G. BLF with other extensions works fine. But how can i use a mobile number? the LED should be green.  fnc=sd;sub=mobile_number@10.4.3.253:5060;nme=nameOn the SPA525 this works. But not on the 514G. ...

We have a number of SPA-509G phones with SPA-500DS attendant consoles attached and want to use them on an Asterisk based SIP system. everyone keeps saying that the soft keys on the 500DS should be programmed:fnc=blf+sd+cp;sub=name@$PROXY It doesn't w...

Hi,i have spa504G (sip version)+spa500s  and CUCME (cisco 2911, Version 15.1(2)T1).I haven't found any guides about this issue. Is it possible to configure speed dial buttons on spa500S? Thanks a lotAlexander

Hi I have a SPA112 with 2 phone numbers on, one for each line, how can I make the calls from both lines ring on fx. Line 1 or both Lines? I have only one phone attached that is the reason. Also is it possible from line 1 to make outgoing calls on Lin...

I have a SPA2102 and it has been working fine until now. I now have a blinking green power LED flashing. I have reset by removing the power cord and I still have the issue. Any recommended fixes? Thanks in advance.

hello, I can not configure 2 SPA3102 gateway model;is a gateway into the A site and I have to use the FXO port to carry an analog line at Site B on the FXS port of the second gateway, but I can not configure the interfaces.can you give me some help, ...

Visiting a client site tomorrow and he is on 7.5.4.  He has asked whether 7.5.6 is okay to use.  Problem w/ 7.5.4 are some occasional audio problems, which I think are fixed in 7.5.5, but wondering if I shouldn't jump right to 7.5.6. Thanks!

I purchased spa2102 4 days ago but now I can't configure it via a web browser.The status bar info says 'connection limited or no conectivity' so typing 192.168.0.1 gives no result, but the same cable works when plugged to a router.I tried also  to co...

I'm trying to recover a SPA502G that was working OK before an attempted firmware upgrade. The recovery.exe (V7.4.4 and V7.5.2b) says "Before proceeding, please confirm that the SPA's Status LED is blinking repeatedly..."My status LEDs do not blink. T...