Hello everyone, I am trying to connect 2 analog devices(not phones) using SPA3102.However the difference with normal analog phones is that when you connect a phone the SPA understands when you Off Hook it,these devices however when connected to Line1...
I wonder if someone could clarify the following please?In the Cisco UC540 - 560 platforms we have an embedded SNR feature. My question is; what features do we have from the mobile device?If I answer the call on a mobile can i?transfer the call back ...
I have UC540 with 7 BRI lines. Now we got PRI line. Can any one help me how to configure a PRI line.step by step.Also if I am using CA and if icreate a new site on working hours and do a new pri set up in that will affect the existing BRI. Please som...
For USER english:Scenario:1 spa 3102 - 1001 UserA SIP server1 spa 921 - 101 user1 spa 922 - 102 userThis is what happens:101 user call external line to 0622222 ....sip server route call on SPA3102spa 3102 call 0622222 .... and connects with 101While ...
Hi GuysI am struggling to setup a network for UC320W with SPA504G phones and SG200-50P switch.I chose the 1st topology i.e UC320 will act as data and voice DHCP server.When I plugged the phones in they took a lot of time to get the IP address and got...
We have purchased a license for WebEx Meeting Connect Small Biz. Does it get added through the License Management PAK license or through the Smart Applications Manager under WebEx PhoneConnect?This is on a UC540 running Software Pack 8.1Please advis...
The call forwarding works fine. My only problem is when I try to redial if I don't get connected in my first attempt because the line will be busy for one minute. I will have to wait for one minute before I can redial.Deatails of how I make the cal...
I am using linksys pap2 phone adapter with nonoh.net Voip When calling via pap2 - nobody can see my phone. Or CID work wrong & person I call see wrong phone #. WHen I use nonoh net special programm for calling - not via PAP2 - I can congigure it f...
Just trying to confirm the following, for a remote teleworker to access our office from his home office using a 7961 he will require at least the Cisco 870 series and should it be the ADSL version? I do not see how the Ethernet version will work?Sho...
HiWe have a UC540 with SNR configured on an extension. If the extension is called from an internal extension then the SNR works exactly as it should. However, if the extension is called either from the DDI number associated with the extension or via ...
Hi,I ran into a weird issue today setting up a UC540 :We created a blast group with 15 SPA 5xx phones and one fxs port (set up as a user phone for an analog wireless phone), but when trying to call the group, the system would just reboot on itself......
Hi,Has anyone ever tried hooking up some old paging amplifier (the ones you plugged into the paging port on plain old pbx systems) into an fxs port on the UC540 ? Or should I be using an fxo port instead ?Thanks.
Please let me know if this is a known issue, and if there is a workaround or fix coming.Here is the setup: UC320 with voice lines on FXO. Receptionist phone is a 525G2 with a 500S module. 500S Module has BLF buttons for all users, plus auto-dial butt...
Hi All,Hoping someone has seen this before.I have a FXO line coming into a UC540, and have programmed it as a 'CO line' on the first button of a SPA525G phone.The line works fine for outbound calls. For inbound calls, the phone will not ring. The k...
Hello, i hope someone can help me, i have an SPA9000 and an SPA400, The SPA400 detects the pstn line in the Config. Webpage, but none of the leds turn on when i connect the PSTN line to a FX0 port, i have tried to run the setup and doesn´t detect the...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: