Hi,Im getting some messages stating that packages are being dropped.%FW-6-DROP_PKT: Dropping Other session <my ip>:2814 <remote ip>:443 due to RST inside current window with ip ident 51674 tcpflags 0x5014 seq.no 1099894245 ack 3238826067I'm also ge...
I got this question from one of our partners in Kazakhstan.Is it possible to create a common corporate SkypeID that will be used as one of the lines of communications with clients, i.e. example, button on a Skype to call from skype, when it is press...
Is there a simple way to set up a second AA in CCA?My customer has a second division that has a separate published number. They want a separate AA for the callers to access when the number is called.They have a main inbound number that hits the AA, ...
Phone configured to get jpg using http against IIS6 serverPhone requests the image very 5 seconds even though no HTTP refresh timer set by the serversame config with .bmp image on SPA962 to same server works fine (Image is loaded once)
Can I include an off-site extension (e.g. a phone on a second or third CME or SBCS site networked via IP trunk) in a call blast or parallel hunt group?
Hi,I created 2 dial peers:UC520(config)#dial-peer voice 104 pots UC520(config-dial-peer)#destination-pattern 9.T UC520(config-dial-peer)#port 0/1/0UC520(config)#dial-peer voice 105 potsUC520(config-dial-peer)#destination-pattern 9.TUC520(config-dial-...
Hi,I have a SPA504G but I don't konw how can I set italian language and regional tones.There are no instruction on how can I upload Italian language dictionary into the phone.I have the latest firmware but I don't have the dictionary.How can I do ?
Are the SPA 500 phones compatible with Comms Manager BE 7 and will the BLFs work in this environment over SIP?
Hi Cisco Team,Just a couple of questions about a couple of features on the UC-500.B-ACD Funcitonality:Is there any practical/programming or other reasons as to why we are not able to have to the B-ACD talk to a blast group instead of an ephone-hunt g...
I am trying to configure the SPA525G phones with the UC500 box, however it only works when uscing SCCP, when I switch to SIP, the phone stops working. I found a few documents googling it but nothing that gives me a complete handle on how to configure...
Has anyone had an issue with users receiving blank or dead air recordings in their voice mail box?Our customer has a UC540, an ESW, and softphones. A lot of users had this isuse, then we replaced the ESW switch for other reasons ( bad ports) and now...
I have what appears to be a SPA3102 firmware bug. The problem can be duplicated and is repeatable. I am running SPA3102 firmware 5.1.10(GW).After you receive an unanswered pstn call with ring-thru to the phone attached to the SPA3102, on future out...
All,I had posted back in mid-2009 about our 4 7911's being off by 4 hours, well, I just noticed they are off by 5 hours, but all the 7940' and 60's are perfectly fine. In the previous post, I was told to look at the telephony-service, which I just c...
I work for a church that has a UC500 system in place. Thay are looking for a way to leverage their VoIP system to call church members and send them a voice message for general information, closings due to weather, etc. They have a mix of English and ...
When connected with the Cisco Anyconnect client the IP Communicator will start and register with system correctly. However, I'm not able to make calls with it (don’t get a dial tone) and every 3 minutes or so all the softkeys will disappear and then ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: