Hi all, following the debug of a updated vpn client trying to connect to a vpn concentrator with certificates auth :11:23:23.559 01/27/06 Sev=Info/5 IKE/0x63000001Peer supports DPD11:23:23.559 01/27/06 Sev=Warning/2 CERT/0xA3600022Failed to verif...
Hi all, following the debug of a updated vpn client trying to connect to a vpn concentrator with certificates auth :11:23:23.559 01/27/06 Sev=Info/5 IKE/0x63000001Peer supports DPD11:23:23.559 01/27/06 Sev=Warning/2 CERT/0xA3600022Failed to verif...
Hi there,im using 3x PIX 501. The first is the Easy VPN Server an two are Clients. The Easy VPN Server Pix is connected on an 2Mbit SDSL Access. It uses a PPPoE Dial in Connection. The Problem:The Server PIX disconnects the PPPOE Session very often.M...
HiI know its possible to configure split tunneling on the PIX501, but is it possible to configure, that everything is tunnelled, besides the local lan you are connecting from. That option is available on the VPN3000 Concentrator.It would be nice to a...
Hi,I'm connecting to a pix 501 with the cisco vpn client 4.7. It works if I do not have the match address acl in the dynamic-map, but fails if I put the match address rule in.Works:ccess-list nonat permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255....
HiCould anybody please tell me what is required to have a dial-up server running analogue and ISDN access (prefered on AS 5400 or AS 5800 series)ThanksMark
Hi,I wonder if anyone can help with this situation.We have a number of remote sites which connect into our head office using ADSL. The remote sites have Cisco 837 routers and communicate with head office over IPSEC tunnel which terminates on our PIX5...
i have a strange problem i just want to clarify i have enabled client mode vpn with xauth. the client router asks for xauth and the server is configured with save password command.the client router prompted once for username and password then the cli...
Hi,I have a VPN established between two sites, i see that the VPN establishes well but i am unable to comunicate with the other site.What i wanted to know is if there is any command to debug traffic coming through this VPN so i can try to figure out ...
I have a PIX behind a cisco router with two wan interfaces. PIX uses router as a default gateway. I have policy based routing on router and static routes out of each - 1 as backup for the other.I have enabled PIX for NAT-T and all works ok over pri...
Hi,Does anyone know what the max VPN throughput for an 837 ADSL router using 3DES IPSEC? I looked on cisco.com, and didn't see any hard number on performance. I know the 837 uses hardware encryption acceleration.Thanks!
Hello!I configure the VPN IPsec and NAT feature on the same router. I would that traffic which going to my site via VPN shouldn't be nating but traffic to Internet should. How I should configure my router to resolve problem?Thanks a lot
VPN clients connect to VPN concentrator. Clients get an IP address for a static pool in the range of 10.1.100.240-10.1.100.254. Internal interface has an IP in the same network. A tunnel default is configured to send packets to 10.1.100.1 which is a ...
Hi There,I am banging my head a bit here. I want to encrypt all traffic between 2 sites except voice. On cisco's site it would seem that the "crypto map" command should appear on both the physical (in this case dialer) and on the Tunnel interface. ...
We have 3825 as the DMVPN server and trying to build tunnels using 831 remote routers connected over Cable or DSL. The tunnel keeps going up and down. Can someone please provide a sample config.Thanks.
Dear all,we want to configure a 3640 router with a dual e1-pri card to cover following tasks:- dial-in (X.25) and protocol translation to TCP- dial-out (protocol translation from TCP to X.25, routing to a dialer)Unfortunately we have the problem that...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
12-04-2024 07:13 PM | ||
11-26-2024 09:57 PM | ||
11-25-2024 01:44 PM | ||
11-18-2024 10:14 AM | ||
11-14-2024 10:44 PM |
User | Count |
---|---|
3 | |
2 | |
1 | |
1 | |
1 |