VPN

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Cisco CyberSecurity

Labels

Forum Posts

Hi!I have to site A and B connected by Site to Site VPN and they areworking OK. When I try to add remote access VPN for Site A so thatusers at home could use Both site A´s ja Site B´s services and alsoconnect to net through site A, I can't get this ...

muusitalo by Level 1
  • 389 Views
  • 2 replies
  • 0 Helpful votes

Resolved! VPN & ACS question

Hi, This may be a stupid question but I need to learn about security issues so here is my question: if remote end users can access to their Corporate network via VPN securily then why do they need ACS solution ? Thanks for educating me.

netman2k5 by Level 1
  • 645 Views
  • 4 replies
  • 0 Helpful votes

HiI have a L2L VPN (1721 Router to 3005 Concentrator) that has been working flawlessly for six months. Prior to the L2L, the five clients at the remote office were all connecting to the concentrator using the Cisco VPN Client. This week I needed to...

joe by Level 1
  • 417 Views
  • 2 replies
  • 0 Helpful votes

HiI have vpn services setup on our Pix 515I have 2 internal networks behind my firewall.Network 1 is on the same subnet as the pix inside interface.Network 2 is one hop removed on another vlan. Traffic is passing between these 2 netowrks and both net...

skcarter by Level 1
  • 585 Views
  • 7 replies
  • 0 Helpful votes

I have a VPN group setup that allows the clients to connect and access everything on the internal net. I would like to set up a seperate group that hands the client a 10.43.0.1 IP address and limits it to telnet an 10.60.1.20 address. I believe I nee...

pvh-cisco by Level 1
  • 540 Views
  • 1 replies
  • 0 Helpful votes

HiI am trying to setup VPN using Microsoft CA with eToken. The process http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080094e69.shtml has been followed.Now when I try to connect to firewall via VPN client 4.x, I ...

I understand that spoke-to-spoke comms is not possible if the input and output interfaces are the same because ASA doesn't allow this but is spoke-to-spoke comms possible if the spokes are on different interfaces eg e0 and e2?Barry.

b_learoyd by Level 1
  • 624 Views
  • 7 replies
  • 0 Helpful votes

I would like to setup a LAN-to-LAN VPN connection between my corporate office (VPN3005) and some home office users. I have purchased a Linksys RV082 router and a Linksys BEFVP41 router to test. The home office users will be using dynamic ip address...

donc by Level 1
  • 504 Views
  • 2 replies
  • 0 Helpful votes

Hello all,I need help with my problem ...its related todigital modems..Mica modems.We have those ones configured in C3640 and our clients are connecting from analog dial-up modems to us. Problem is that sometimes it function connect with dial-up and ...

johnleeee by Level 1
  • 580 Views
  • 2 replies
  • 0 Helpful votes

I have a LAN-to-LAN VPN connection between a Cisco 2691V at my main office and a Cisco 831 (DSL) at a remote office. On the other side of the 831 is one HP printer and 3 computers. At night when they power down the computers and printer, the VPN co...

---dsl connection----pix(DMZ(security 50)----inside----host1) i am unable to ping the public ip of pix DMZ interface.2) i am running a ipsec tunnel which terminates on the DMZ interface.3) when i try to connect thro VPN client ,its say trying to conn...

tchacko by Level 5
  • 478 Views
  • 2 replies
  • 0 Helpful votes