Hi,We are planning to upgrade our current ASA with Anyconnect 3.x to 4.x. The hostscan 3.x we are currently using, have the option on the ASDM for Secure Desktop => Prelogin Policy option.We extensively use this Pre-login policy to differentiate dif...
Forum Posts
Hi All,I have an issue on ASA by moving anyconnect images under context. so please need your help.
I'm looking for a way to monitoring the usage of an IP-Pool on Cisco ASR9000. Until now we are using ASR1000 with SNMP: - cIpLocalPoolFreeAddrs (1.3.6.1.4.1.9.9.326.1.1.2.1.5) CISCO-IP-LOCAL-POOL-MIB But i'm unable to find a equivalent OID on IOS...
Hi, I am currently looking to achieve the following in terms of remote access to my network estate: * restrict external VTY access from management platforms & customer appliances * allow unrestricted 'internal' communication (using the local devic...
Resolved! Cisco VPN AnyConnect
Hi, I am looking for VPN notification or Alert kind of service in AnyConnect, once the VPN connection established as a admin we should get some alert, can anyone help me out to trigger the alert .... Best regards, Pramod M
I got the connection between the two working, both sides show an active connection. That being said I cannot talk to between the two, I can't ping servers on remote side and vice versa. I've been staring at the config, could use some new eyes. The...
Hello, We are in the process of changing the way we assign user VLANS. We are switching from assigning them based on location to assigning them based on user/role. In our current setup we are using AnyConnect, Cisco 5515 ASA and Microsoft Radius/NPS ...
I have a problem with my umbrella-integrated OSX AnyConnect 4.5.02036 installation due to a permissions issue with the cache. The guidance for correcting the problem is to clear the cache, but I have no idea how to find it!
Hello Experts IPSEC vpn filter ACL are applied for inbound traffic or outbound traffic only? Also if no vpn filter ACL configured, then outbound traffic is allowed as per inside ACL? Also if vpn filter ACL configured ( (whose last statement is deny...
I have a site-to-site VPN using 2 Cisco ASAv. It looks like the IPSec tunnel is up but I can not reach the other side of the tunnel. It looks like my crypto map is correct but I cannot ping or telnet. Below is a basic topology and I attached some con...
Hi All, I have a design question about my client network. Refer to the network diagram, originally, the traffic from Taiwan to Germany should flow between the MPLS network. However, the MPLS connection in Taiwan will discconect soon. So we need t...
Hi All,We're currently working on a customer POV wherein we need to push customized NAM profile (wired only) to anyconnect. Can this be done via SCCM? or can only be achieved through client provisioning from ISE?Requirement:Made a customization of NA...
Hi Guys. I have ASA 5516 and lots of VPN remote access users. I use CLI command to get access to the vpn: username xxx attributesvpn-simultaneous-logins 1 or 0 (On OFF) is any command to get access to all users assign to gruop policy or any comma...
Resolved! Dual DMVPN
Hello All, What I would like to do is have a hub that has dual DMVPN tunnels to the spokes. The ultimate goal of our network is to have the spokes authenticate to each other using PKI with IKEv2 on the tunnel. Right now, I can get the the spok...
I'm trying to configure an Ipsec vpn gateway to gateway between Cisco 891-24X (using Cisco CP Express 3.5.2) and Cisco RV325 (firmware v1.3.2.02) routers. I'm trying to setup on Cisco 891 a static site-to-site VPN selecting IKEv1 key exchange model a...
