Data Center and Cloud

Resolved! ACI forwarding question:

ACI forwarding question: usually in a single pod when an endpoint wants to reach with in the same subnet but it dest not known it will send a spine proxy to one of the spines. And Spines check for the endpoint if not present it will drop it won't flo...

UCS 5108 mini errors

Hello.What are the errors on the UCS 5108 mini?

ACI with DMZ Servers

Hello Freindswith Regards to ACI with DMZ Servers can we provision the DMZ Servers (Web-DNS-Mail) directly on the ACI Fabric in Main Tenant aka(Production Tenant) instead of having Dedicated Tenant for DMZ Servicewe Already have PaloAlto at Internet ...

ASA in Active/Standby Mode connected to ACI

Hello Freindsfor ASA in Active/Standby Mode connected to ACI , do i need 1 IPG(vPC) For Both or Just 2 IPG 1 for each device? I know 1 IPG for both ASAs if they are in Cluster Mode but confused in Active/Standbythanks all

Nexus 5672UP – Ethernet Ports Not Visible After Slot Reset

I have a Cisco Nexus 5672UP switch running NX‑OS 7.3(6)N1(1). The switch was functioning normally, but after performing a reset, the Ethernet ports on Slot 1 (ports 1‑48) are no longer visible in show interface status or show interface brief.

DS-C9132T-MEK9 - connect datacenters

Hello , can you please tel me if i need additional licenses something like Brocade Extended Fabrics for DS-C9132T-MEK9 switch? we have to connect two datacanters about 5 km far away from each other

ACI Expansion to a Second Data Center Without Multi-Pod or Multi-Site

Hello Cisco Community, I am looking for guidance on a design scenario involving a brownfield ACI deployment across two data centers. The customer operates two data centers: DC1 is already deployed with Cisco ACI. DC2 is currently running a traditi...

Resolved! Does N9K-C93180YC-FX3 & N9K-C93108TC-FX3 support FCOE in ACI mode?

Hi, Does N9K-C93180YC-FX3 & N9K-C93108TC-FX3 support FCOE in ACI mode? Thanks.

Design/Recommendation for ACI Multi-site Architecture with ASAs & F5s

Hello FreindsI Have 4 x F5 BIG-IP i5800 Hardware, need to provision 2 per Site in Active/Standby mode, ACI Multi-site ArchitectureI Have the following questions4 x F5 BIG-IP i5800 Hardware1. What is the Recomendation for the Failover Link, Back to Ba...

Monitoring Cisco ACI with PRTG

If you would like to monitor your Cisco ACI with PRTG, have a look at the feature request in the User Voice portal of Paessler and leave a vote. https://uservoice.paessler.com/forums/965997/suggestions/50680976

WAN Optimizer Interoperability Between Cisco WAAS and Juniper WX

Hello WAAS Experts,Can Cisco WAAS communicate with Juniper WAN Optimizer? If so, which Cisco and Juniper hardware models?Thank You,Audie

upgarde ucs c240 server firmware connect to UCSM

i have a cisco UCS C240m5 server that connect UCSM, i want to upgrade this firmware ,do i upgrade from ucsm or server cimc

Resolved! [Nexus Dashboard 4.1.1g] - [ESXi] - [Issue after power down/reload]

Hello team,I installed ND 4.1.1g with the ova on esxi 8.x. I follow the deployment guide with the pre-requirements, basically : - 16Vcpu-64G of ram-SSD disk (50 + 500G)-Add vlan 4095 on the data interface in the parameters of vswitch-Deactivate time ...

Resolved! Nexus 9332C Booting ACI image from boot loader issue

Hi Guys, I am looking for some help as I hit obstacles and I think that I have tried all possible options, to get this issue resolved.So I was converting Nexus 9332C from NX-OS mode to ACI mode to version aci-n9000-dk9.14.2.6o.bin and at some point p...

ACI TAC Team - MS deployment-guide-for-aci-fabrics -4.1.1.g

Hello ACI TAC TeamAny Plan to update the below to NDO 4.1.1ghttps://www.cisco.com/c/en/us/td/docs/dcn/whitepapers/cisco-multi-site-deployment-guide-for-aci-fabrics.html Thanks

Data Center and Cloud

Browse the Community

Cisco Developed UCS Integrations

UCS Director