HiWe have a Cisco 9800/Cisco Lightweight network. The main wireless profile is used by devices that are a mixed of managed (Intune) and BYOD and runs 802.1x EAP-PEAP using Cisco ISE 3.3 for AAA services. I have been asked to roll out EAP-TLS for th...
Bonjour,J'ai récupéré un point d'accès Cisco Aironet AIR-AP3802I-E-K9 d'occasion (pas acheté auprès d'un revendeur, aucun contrat de support associé à l'appareil). Il tourne actuellement en image CAPWAP (Cisco AP Software, ap3g3), confirmé via show i...
Hello community,We would like to get your guidance on the following customer requirement and understand how this could be implemented using Meraki. The customer manages its Windows devices through Microsoft Intune and would like to authenticate machi...
I have a 9800-40 that has APs at our local office as well as remote offices. Same guest wireless SSID. Remote office wants guest wireless disabled after hours, but local office needs it on. I created a calendar profile, but if I map it to my guest...
Hello, We have a new site where we are planning on installing brand new WAP units (CW9166I-B) and C9800 WLC. This is a green field deployment. Our wireless vendor is telling us that the CW9166I-B units are Meraki Cloud and not Cisco when you first i...
Should new RF Profiles be created when deploying new access points at a site, or should the default profile be used?If creating a new RF Profile is recommended, which configuration settings should be modified? We will be deploying CW916xx APs. Any in...
Was there ever a real response / solution to the original question ?Because I think I might have the same problem.9800 -> Configuration -> Services -> Multicast - Wireless mDNS Bridging (enable or disable)What is the equivalent CLI command ?Our scena...
Hi everyone,I have a question about the Cisco Meraki CW9176I and CW9172I access points. While reviewing the installation guide for both models, I found the supported operating capacities based on power source and Ethernet speed, but I couldn't find a...
Hello, I am currently testing a Cisco Catalyst CW9172I Access Point with a Cisco Catalyst 9800 Series Wireless Controller. Environment WLC Model: 9800-L-F-K9Software Version: 17.15.4dAP Model: CW9172ICountry:Taiwan⸻ Issue The AP successfully joins th...
i have 3 9130axi-d and 3 3802I aps connecting to 3850 switch there is no controller , i have converted one of the 9130 AP to EWC, which is wlc now having version 17.9.10, but rest of the aps are not joining the controller getting obms image failed, i...
Current WLC: C9800-CL on 17.3.5a (Amsterdam) & Current AP version 17.3.5.42AP Models: 1542I/E, 2802I/E, 3802E, 9115AXI, 9120AXI, 9120AXETarget Platform: C9800-L - 17.9.4aCould we migrate on target platform or not, if not please suggest best migration...
Datasheets for the CW9177 say that it is supported by the 26.1.x release. However, when looking at the release notes for 26.1.1 and 26.1.2 it never mentions the CW9177 being supported. Am I missing something?
We are testing 6 GHz on CW9176I APs running MR 32.2.4 and seeing an issue with Windows clients discovering a 6-GHz-only SSID.Test setup:6 GHz onlyWPA3 enabledPMF enabledRADIUS excluded for isolation testingResults:6 GHz-capable iPhone → SSID visible ...
Access points software versions MR 33.1.3 changelogInfoDetailed release notes available at: https://documentation.meraki.com/Wireless/Product_Information/Compatibility_and_Firmware/MR_33.1.3_Release_Notes
Hey all,Just wanted to confirm that this also works with the new Cisco WLC 9800H RP using a 1G GLC-SX-MMD SFPAfter spending long time on tshoot, I found that the RP port would not work with a 10G-SR SFP, Once I replaced it with the 1G GLC-SX-MMD, the...
