Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello Cisco WLAN-Experts,we will soon run out of users on our two 9800-L-C-Guest-WLCs crossing the border of 5000 concurrent users:-------------------------------------------Wlan-name ID Client count -----------------------------...
Hello, i have been trying to compose a report of clients connecting to the 2.4 ghz Wifi via the event log, i have been able to get the 802.11 association but that is pulling the 5 ghz as well, I'd rather not have to scroll through thousands of entrie...
Can I use this antenna with 5GHz?Is 802.3bt required?I want to install it for a warehouse at one end, replacing ANT2566P4W-RS= I have RF devices 1x1 stream Please, I would appreciate your answer
What are the differences between types of Client IP assignments for SSIDs? Meraki DHCP, Local LAN and L3 Roaming...
Hi everyone, I'm currently facing an issue with the Embedded Wireless Controller (EWC) running on Catalyst 9115AX Access Points. We're using MAC filtering across all WLANs (SSIDs) to control access to the wireless network. Each device’s MAC address (...
hello everyonethese days i am experiencing a problem due to Redirect ACL failure message,below i am releasing the details of my EWLCEWLC firmware 17.6.4I checked via wireshark the response received from cisco ise and indeed the connection is accepted...
Hello, I tried to launch a job on my Cisco Prime (current version is 3.8.1) to archive the configuration of my Cisco 9800 WLC, but the job gave me the "Partial Success status". Either the Running and the startup configs are successful, but the "Fetch...
こんにちわ。 C9800-L-C-K9無線コントローラにおいて、 ファイアウォールのようなポート設定ってあるのでしょうか？ 例えばコントローラ上でTCP80を開放したいんです。 となった場合の設定方法を教えてください！！ ドキュメントやGUIの設定画面を探してもどうしてもわからなくて。 よろしくお願いいたします。（そもそも無線でポート遮断という概念があるのか？）
Hi guys! Hope you all good!I had issues while deletion of users in the user management portal some days back. I keep deleting users which are expired. Recently when i deleted users in bulk, the valid users got deleted (nearly hundred users). I select...
Customer had some update done on Aeroscout and since then NMSP is inactive Controllers: 2 5508 in HA mode running 8.5.140 MSE 3355 running 8.0 Prime version 3.4 Verified the Auth list. readded the Hask Key shown in MSE. in the debug it shows handsha...
I need to know what the access points' joining procedures are in SSO deployments and N+1 deployments, and what the timers are in each section. For example, in SSO, if the primary controller fails, what will happen with the access point, and if it com...
Hi team, we have installed c9800 HA pair 2 months ago, running 17.12.4 version. We are facing now random reloads of standby WLC every few hours with this info: Reload History: Reload Code: ReloadReload Description: Reload Command - RIF: Bulk Sync, sy...
Hi,I need to select an AP which has below specs.2.4 GHz 802.11b/g/n/ax and 5 GHz 802.11a/n/ac/ax, Device throughput of 1.5 Gbps, AP should support 2 x 2 multiple input, multiple output (MIMO) with two spatial streams, AP should have 1x 10/100/1000 BA...
Hi community,I'm having a problem with some MR44 access points. Support wants me to provide the SDB, but the APs neither respond to a ping in the management network nor do they broadcast an SSID in case of error. How do I access the SDB if the AP can...
Hi Experts, I have setup where Clients connected on WLC-9800 SSID should get Vlans assignment from Cisco ISE authorization Profile, But it still clients gets IP from Access Policy configured on WLC-9800AAA is configured on WLC with Mac Filtering and ...
