Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! C9800 pki auth error
Access points are not authenticating on Cisco Catalyst 9800-40 Wireless Controller 17.9.5.Monitoring > Wireless > AP Statistics -> No reboot reason | AP Auth FailureAP models: C9130AXI-Z and IW6300Trace logs: AttachedAny suggestion?
Hey all, I'm just curious what your guyss process is when setting up powers for campus situations with many rooms back to back. We only have max 30 people per class with an mr56 per classroom, and it's currently in a spot where each classroom serves ...
Hi there,We are experiencing a high volume of 802.11 Disassociation / Unknown Reason events across our wireless LAN. The issue is intermittent, and does not affect all clients at the same time. The issue is evident across different SSIDs (we have 4 a...
Hello, everyone. I understand that noise are signals that operate on the same frequency as, for example our Wireless signal. I just need to a clarification to how it differs with interference. So if I understand this right, as long as the noise or th...
Resolved! 9800 vty priv access
Good Day, Procedure to create a user via GUI that has vty priv15 access? Thanks & Regards
Been using interface groups for years, something want to check.Recently we migrated our DHCP Servers, 1 of the vlans in the interface group missed the missed the new IP.The old sever was shut down, so no devices should have tried to get an IP.I saw t...
Hi All,Facing issue in the Meraki wireless deployment I have created 2 SSIDs one for CORP and one for guest and using different VLAN.If i can my laptop to meraki AP an getting the IP of the VLAn mapped to SSID but in gateway im getting the IP address...
I am installing an MR-86 outdoor Wi-Fi access point, and I have a scenario in which 180 degree, longer-range Wi-Fi coverage would be beneficial. The user density is low. If I connect two MA-ANT-27 antennas, each connected to one 2.4 GHz and one 5.8 G...
Hello Experts,9115AXI-D AP connected to 9800 WLC Blinking RED-GREEN-BLUE Continually.This could be due to power level or any other reason? Troubleshooting done so far -->Connected AP to different switch ports of 6500 / 4500 No luck.Switch port Power ...
Hello,I hope you're doing well.I am working on a wireless communication setup using a single Cisco Catalyst Access Point (model 9162I) and would like assistance configuring it to use multiple channels simultaneously on the 5GHz band.Here is the scena...
I am receiving thousands of rogue AP alerts on Prime and want to turn off the alerting. How do i do this.?
Hello,I purchased a new Access Point Cisco Catalyst 9162I. I want to set different channels so that my devices could get connected to that and receive data from different channels simultaneously how do i achieve this. Regards.Pranav Ghabade.
Resolved! Meraki Splashページの仕様について
Meraki SplashページのWelcome Messageがクライアント(スマホ、PC)によって中央揃え、左揃えと表示が統一されておりません。左揃えに統一したい場合、HTML/CSSをWelcome Messageに適用するしか方法は無いでしょうか。HTML/CSSの知識が無い為、他に方法があればご教示頂きたく思います。また、Splashページで新規ユーザを登録する際、Merakiダッシュボード上でアクティベーションメールの有効時間を変更することは出来ますでしょうか。
Hi everyone. How i made the downgrade firmeware? when i connect my ap to console port, my terminal by serial stay black. nothing appear. And when i connect by tftp, says timeout....please help me.thanks for support and sorry for my english.congratula...
Hello, everyone. I am studiyng for ENCOR and I have questions regarding watts and decibels. Fortunately, it’s only theory since I understand the calculations. My book says the following: I get what’s happening here but not the explanation behind it? ...
