Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! WLC Load Profile Failure
Hi AllAny ideas on the issue below would be much appreciated: 5508 WLC v7.6 code, with 4x 3702i AP's attached, 10>15 Wireless clients average on x2 of the AP's (the Cisco stats say these AP's should handle 128 clients if pushed to their max), the oth...
Resolved! Virtual WLC certificate problem
A problem occurs when trying to install a WebAuth certificate: TransferTask: Sep 19 10:04:47.389: Adding cert (7998 bytes) with certificate key password. *TransferTask: Sep 19 10:04:47.389: Add WebAuth Cert: Adding certificate & private key using pas...
Hi, for HA SSO following topology is being used: Core 1 is primary for spanning tree and HSRP VLANs used for SSIDs offered by WLC1(primary) & WLC2(stanby). WLC1 & WLC2 configured in HA SSO mode and connected via etherchannel to core switches. M...
Hi, I am planning an update to our WLC and AP's (2602s) and wanted to clarify the behaviour around the pre download function. We are going from 8.0.152.0 to 8.3.143.0 I know from both the GUI and CLI you can issue a command to pre download soft...
Hi, I'm replacing an existing network of autonomous APs with Cisco Mobility Express (v 8.7) using 2802i APs. We use a total of 3 BSSIDs on this network. For business reasons, we want certain APs to only include a single WLAN BSSID. Via the Mobi...
Resolved! joint AP to wireless controller 2504
hello all,I am new in wireless , i have Cisco wireless controller 2504 for 50 access point, access point 1262 and switch 3560.i setup the controller correctly and i contect it to the switch and connect the AP to the switch.i can ping from the AP to ...
I have a warehouse with 3700 AP's all using only 5GHz with 2.4GHz disabled. In the warehouse we use both the MC3190 and MC32N0 scanners. I am getting a lot of complaints about network issues by users of the MC3190 scanners. When I run link tests t...
We tried to take backup of Cisco prime for one of our end client using remote repository. But the problem is now the backup size is 43gb and the ftp server size is only 17gb. So it failed. Is there any other way to take backup apart from defaultRepo?...
Hi, we are planning to migrate our wireless solution from cloud based solution (Cisco Meraki) to avoid yearly recurring subscription expense. currently Meraki APs (total- 75 qty) are working at HQ and Branches (10 offices). all branches are connected...
For quite some time, performance on the office extend solution for our internal end users has been exceptionally poor, basically unusable to be accurate. However VPN connectivity via AnyConnect or an IPSEC VPN client was fast.I do know the solution u...
Hi, We have a Cisco , and the customer want to have 3 WLAN, but he want to have one captive portal for each WLAN, only have the WLC he don´t have some external server, it is possible to have three different captive portals in WLC locally? Thanks.
Hello, I'd like to access to the reports folder on the NCS using a ftp software (filezilla ftp client ), how i can get the reports? anyone can help me ??
Hello, I'd like to access to the reports folder on the NCS using a ftp software (filezilla ftp client ), how i can get the reports? anyone can help me ??
Resolved! WLC2504 N+1 Reboot without failover?
This seems like a simple question but I can't find the answer... How do I reboot the primary WLC (in this N+1 failover pair) without the secondary taking over? Do I physically have to power it down/pull cables on the secondary or is there a trick?
I have been training to get this figured out and come to an end. I have an internal SSID connected to management interface and works fine. port 3 IP scope: 172.16.151.200 Sub: 255.255.252.0 Router/Gateway: 172.16.151.1 dhcp server: 172.16.151.15 wo...
