Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Resolved! Rogue AP
In the WLC we can contain the Rouge AP, but how we can make sure our AP is not contained by neighbor WLC if the my AP located not to far with neighbor AP?
Model Name: DN2-HW-APL/ C9800-40 Software Version: 2.3.5.4-70852-HF3 ■Inquiry Contents In an SDA network environment, if you mix C9105 and C9115 access points, Are there any problems with wireless operation or Assurance? For C9120, the Deployment G...
Hi ,Any wireless Guru that could help me troubleshoot/understand this issue that we are having ? Since we upgraded to MR29 ( I tried ANY versions of MR29 ) , users are randomly getting errors ( 20-25s of packetloss ) on reassoc. SSID is WPA2-Enterpri...
I have a thinkpad laptop (490s) with an 802.11ac card in it. I takes like 1 minute for that laptop to connect. What's worse, when it goes to sleep, wakes up - 2 minutes. Also, every 2-3 hours it disconnects and takes a few minutes to reconnect (in ma...
Dear All,we're operating an IoT SSID leveraging the Identity PSK feature in combination with a FreeRadius Server. Now we plan to encrypt the communication between the Wireless Controller and the RADIUS server for this Identity PSK SSID using RADsec.C...
Hi Guys, Our web auth cert is expired, so I would like to replace it with the new one I got. I have a company wildcard cert chain in pem format, it contains the intermediate CA and the Root CA public cert also. I tried to upload it to the Cisco WLC (...
We have noticed that the RadSec Keep-Alive feature is currently implemented by triggering period empty TCP headers with ACK flag. While this is sufficient to keep TLS sessions open with most (intermediate) firewalls, some RadSec server implementation...
Hello, i've encountered a pretty strange issue with Meraki SM.I've configured a SSID security as "Enterprise with: Meraki Cloud Authentication", and assigned a tag to computers (generic tag, called WIFI_Access) . All computers with that tag can acces...
I have 10 Cisco Access Point 1852 working as ME , 9 are working fine but one working as stand alone ME due to diffrenet firmware versionhow to convert or upgrade to the other ME (9 AP)
We are developing an application similar to a DATA LAKE, meaning it will process data and similar tasks. We need to extract some data from Wi-Fi, specifically from Cisco APs and controllers. Which API is used for that?" Is this for a project you're w...
Hi Everyone,Just would like to confirm if AIR-AP3802I-K-K9 supports the flashing LED function. This is due to there's no physical label on the AP, and we would need to identify the AP manually at the site for some reason.I found the documents below r...
Hi All,We have a Meraki WLAN Guest SSID going into a Bridge VLAN, on Meraki Switch, true a Meraki Firewall into the Internet. As it is a Guest VLAN we activated the Layer 2 Isolation. now we need to Whitelist 1. MAC Address witch should be Accessible...
I am planning to deploy Cisco IW9165D CURWB units. One end of the link is to be mounted on a pole. I am being asked for the Wind Loading number. If add a horn antenna the datasheet provides this figure. But I don't see it in the datasheet for the IW9...
Wireless firmware versions MR 31.1.5.1 changelogImportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will not upgrade if they...
Resolved! Meraki firmware upgrade to MR 31.1.5.1
Dear All,I have MR36 and MR86 access points with firmware version MR 30.7.1. I have observed that clients utilizing WiFi 5 are experiencing reduced link speeds, an issue that appears to have arisen following the firmware upgrade to MR 30.7.1.Could yo...
