Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Trying to figure out what is causing high channel utilization on 2.4Ghz channels in our environment. The thing thats really frying my noodle is that if I use spectrum expert to get a look at a channel (Ch. 1 in this case) on a particular AP, this is ...
I run HP/Aruba switches across my school system and have around 600+ MR42s and a handfull of MR52s.Early on and occasionally, I would have and AP go 'bad' in that it will not boot via POE and I bring back to my office and it would work when i used th...
Hello WLAN experts, I'm trying to use the Pi Planning Mode to calculate the necessary number of 2802i WLAN APs for a given area of 1000m² using different protocols. The results are not logical for me. Maybe someone can explain it to me. Besides the...
Hi, We have installed Cisco Access points around our office with two SSIDs, one for the main office devices, and one for guests. The access points use Cisco Aironet 1850 Series Mobility Express. I would like to know if it is possible to block ...
Hi All, I use Cisco AIR-AP1231G-E-K9 succesfully but the same config with the AIR-AP1280B-E-K9 is not possible Could you please help me? I need to deploy the AP 1280B Monday or tuesday ... Config used : conf t dot11 ssid WiFi_Stef authentication open...
For an Access Point(3802i) switch port configuration, should I used trust COS or trust DSCP. My uplink to the core is L2 and I'm trusting COS.
We have a mix of APs in our environment with 3802i units mixed in amongst a mostly 3602i deployment. Has anyone seen any issues with conflicts with having both in the environment? We've had some weird cases of devices experiencing odd behavior in...
Ap 1832i is joining wireless controller 2504 normally. But not broadcasting ssid, another series is working properly and broadcasting except this series.
Edit I meant to post this in the standard Wireless and Mobility forum.. that's what I get for having too many tabs open. Not sure if this needs to be moved or deleted and recreated? Greetings all, I'm trying to evaluate the 1815w units for possi...
Greetings, I am working with a new 5520 WLCs to replace our 5508s. I have everything working except am running into an issue with the guest portal. So, we use a Comodo cert for guest, but it was originally tied to 1.1.1.1, I'm trying to use 10.1....
Dear it may concerns, I have an issue of client distribution for Access points or clients I am currently using 14 aironets(air-ap3802i-b-k9) AP and WLC(Air-ct5520-k9) and have 2 active WLANs; data and voice network) All setting are same as betw...
Hi All, Is there any possibility to generate/export public certificates from a WLC 5508? Our Customer would like to backup his configuration through certificated based authentication instead of user based. I believe there is no way to do that, but s...
Hi Team, We enabled a setting on ISE to begin allowing PEAP session resume and fast reconnect (clients were configured previously to support this) After we did this we are having an odd issue with clients who are coming traveling between a local ...
Hi , I have upgraded wism2 module from 8.0 to 8.3 and i have downloaded both the images like boot image and AP bundle image, and it's succeeded, but when the Ap's are associated to this and stuck in downloading status and the primary image version ...
Hi, I'm configuring a WLC's in foreign + Anchor to handle SSID's for guest access. I'm trying to use an external DHCP server for the IP assigment. I have 3 dynamic interfaces on the WLC Anchor (one for each guest SSID). For some reason when i con...
