Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
hi everybody I have this solutions Cisco Prime 2.2 WLC 8.3 CMX 10.2 (Locations anf analytics) I have many branches offices, In the CMX import all the maps and WLC by the PI In the branches, the maps that import are all the biulding ( 3 floors) but my...
There is some other Cisco appliance similar to Prime Infrastructure ?
HI, I would like know how can I do a migration from WLC 2504 to WLC Virtual.We will migrate the Access Points to, from 1140/1240 to 2700 model. Thanks.
Hello Experts, Clean Air can be enabled globally. Same way can we configure "spectrum intelligence" globally? I have enabled "spectrum intelligence" globally for 802.11a and 802.11b/g/n radios. However the Wireless Access Points have their "SI ...
Hi Guys, I've got a solution which i need to extend to a mobile cabin that is approx 15M from the main site. Is it possible to setup a WGB through the WLC with an IOS AP in the cabin that is then connected back to back to a lightweight unit to mirror...
2 access points are stuck in downloading. They have the default 7.6.100.0 version from factory but we are still in wlc 7.3.112.0 version.We are getting these errors. They are in a remote location. Can I use a special command to reset the device? Or ...
We have a RV340W that freezes randomly. It has 2 VLANs and routing is enabled between them. About 3-4 times a week, the router stops responding to the IP on either VLAN and I have to reboot it. The logs show nothing. I thought maybe something with my...
Hi guys, I intended to upgrade my Switch to version: 03.10.00.E latter. WS-C4507R + E WS-X45-SUP7-E Currently version: Version 03.03.02.SG license Level: ipbase ROM: 15.0 (1r) SG5 I'd like to know what the best method is to finish the upgrade well? S...
Hi I am using a Cisco 5508 controller with sw version 7.4.121.0. I did NOT enable Session Timeout, but I still found station disconnect and reconnect every 30 minutes, I want some way to avoid this diconeect-reconnect loop, does anyone knows? Thank...
Hello Experts, Is there any means to achieve moving of APs to AP Groups and FlexGroups through Cisco Prime? Could not find this in documentation. Moving APs to AP Groups and FlexGroups is a very time consuming activity. Having an option to fac...
HI to all, I have to deploy a wireless mobility express olution with 9 Aps. I would like to know if i configure all of them to act as controllers is a good choice. Or is it better if I configure only a couple of them? I would like to know the pros ...
Hi! I have to set and configure cisco 1832i AP next week. I know how to manage by GUI and create a SSID. However, I don't know to to make a DHCP pool or join into a DHCP server. And how to apply it to a SSID. I wanna try it but my company doe...
I am trying to add this phone as an extension to my pbx. Not sure how to do this, I don't see anywhere I can provision the phone. Is there another device that I need to accomplish this?
we see sometimes on a 3750switchSW_MATM-4-MACFLAP_NOTIF: Host 000b.xxxx.xxxx in vlan 5 is flapping between port Gi2/0/42 and port Po7looking up the MAC we found wifi devices like a pc and handscanner which move to the building thereby changing from A...
Hello Experts, What will be the Significance of AP group when an AP is already moved to an FlexConnect group? When an Access Point is moved to a FlexConnect Group, it still continues to get reflected in the AP group. Why is that the case?
