Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I have a healthcare facility with a pair of 5520 HA controllers that need to upgrade code in order to support the new 'b' regulatory access points. Does anyone have a method of upgrading without any outage or a shorter period outage that they can sha...
Hello, We are using 3702 AP's. Lot of interference is seen in the network but the problem is even 802.11b/g radio is disabled, it shows the interference of 50%, can someone help me out? Thanks in advance
All I have a 5508 on code 8.0.115.0I only use (2) ports. The other (6) are empty. I am getting alot of the following alarms for the empty ports via PRIME 1. Message: Port '3' is down on device '10.x.x.50'.Failure Source: Port WLC-5508/3Alarm Detail: ...
Well the day has finally come to begin testing the link between the wireless bridges. However my cisco 3850 switch that one of the AP's is tied to does not see the AP. I have checked the configuration to see why the switch will not see it, and I am c...
I have 2 5508 controllers that were originally used as standalone controllers. The APs have been moved to another controller and I want to set them up as an HA pair for a different group of APs. The service port isn't connected. Can I configure ...
Hi,We are using WLC 8510 with 8.0.110.0 code, 1131,1040, 1600, 1700, 2700, 3700 indoor APs, ISE 1.3.0.876. We have an eduroam SSID with [WPA + WPA2][Auth(802.1X + CCKM)] an a guest SSID with zero authentication. Both WLANs are using FlexConnect Local...
Hi Team, I have configured OEAP 602i testing with the Corp SSID its working. I noticed that it is Corporate SSID not showing after long idle time at my home. once i have restart the device its working. Every day same issue.Kindly suggest any setting ...
Hi We had some problems with a couple of Flex 7500 series wlc and was thinking of going down from 8.3.x to a MD release. Or maybe 8.0.133 that is also suggested by cisco, even though it's ED.Will the 2802i still be able to join, just not with full f...
Hi In our project there are four wireless controller in two wism -1 module and 211 APS 1042 for WLC1 fail over is WLC4 and for WlC2 Fail over is WLC3 for each APS in High availbility we have to assign primary and Secondary is there any cli commad or ...
Good day, I have configured my 3850 switch with two SSIDs one for guest and the other for internal uses. I have an acs server in my network which is using AD as its identity store. I have been trying to get authentication to work but with no joy and...
Hi,I am facing a strange problem with the AIR-PWRINJ1500-2.At times the injector behaves perfectly fine but once Switched Off & again Powered On, all 3 LEDs, never become stable & blink continuously.Has someone seen such a behavior ? Pls, share. Than...
Dear Techies.... I have a problem in Wirelesss....If I reboot coreswitch or firewall or unplug or replug the WLC cable....means disturbance to WLC, entire APs will go down. APs are having DHCP IPs...when we check on DHCP server there are no requests...
Hi previously the APS 2602 are registering with controller now it join with controller the flowing console output of 2602 AP F1-AP3#F1-AP3#F1-AP3#F1-AP3#*Aug 3 11:45:43.035: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255*Aug 3 11:...
Hi all, after some trouble I was able to migrate my AIR-AP1852E-E-K9 from CAPWAP to Autonomous. It is now running AIR-AP1850-K9-8.2.100.0.tar (I know it is outdated but it's the only I was able to get not having a smartnet). I've some questions ...
Hello I have a problem to join a 1702i AP to the 5520 controller. I have attached the debug capwap and the console output of the AP. On the Controller runs the newest SW Release 8.3.102 Has anyone an idea whats the problem? Thanks for your help
