Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, I´ve had been verifiyng problems with the cisco aironet 1815. Almost every day they crash, it means i can´t comunicate with controller or ap's in the management interface, and before that i see the following message on the log "Did not rece...
Hi all, I do have 3 x AIR-AP3802I-E-K9 and a WS-C3560X-48P with a PS of 1100 W, capable of 802.3at.I can get the APs on the WLC, but they're not broadcasting, and clean air is off. After some troubleshooting, even if I configured the switch interface...
I'm not a wireless expert by any means, but I would think based on the document this should be a simple initial configuration. Going through the document 1815T Deployment Guide it says connect to router and then plug in to LAN3 and go to 10.0.0.1. ...
HI, Can a new 1850 AP join and existing Mobility Express Network, if there aren't any dhcp server in my enviroment to lease out ip for the new ap. The new AP details as below :- AP Running Image : 8.3.102.0Primary Boot Image : 8.3.102.0Backup B...
Good day, I am looking for a way, CLI or GUI to change the syslog port from 514 to 1514 or other as our log server is not able to listen on 514. I've looked in both but do not see any place to change this. Any ideas would be welcomed. Thanks MP
Hello,I'm trying to find a way to pass off modify the password of a Guest SSID used for Meetings to another dept. Is there a way to create an admin account that can only modify a singular SSID or a better approach to this in general? Thanks
Good morningI am trying to construct a meraki mesh.Please answer the following questions.1.Is the same channel of the Gateway AP and the Repeater AP used for the mesh?Also, is there a problem with the mesh link when the client uses the service in the...
Hi Guys, I have an issue where in a mesh network , the MAPs are connected to very far MAPs / RAPs with lower SNR. is there a way to configure minimum SNR for the MAP to start looking for a better Path ? also what is the interival that a MAP check ...
I need a wireless extender for our Cisco DPC3829. I don't know what devices are compatible with it and can't find any thing online. Can someone recommend an extender that will work with this equipment? Thanks
Hello, the new version of vWLC, 8.4.100.0, is possible to install on Hyper-V: http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn84.html#hyperv-vwlc But we can't found nothing about installation, like file to download...... Can...
We are upgrading to PRIME 3.1 (from 3.0.3), and have to start using Smart Licensing ... What are the weights of tokens, for device types: unified access points, WiSM2 WLCs, WLC 2504, WLC 5500, WLC 8540 ?
Hi all, i have a 2500 series AP and i have the Top Client Devices list that show me how much traffic every client do. Could you please, tell me a way to know since when they did the traffic? Thanks, Alessandro
I'm considering use some MR33 to found a mesh network, covering a place do not have wire ethernet access.——ethernet cable——RAP---MAP--MAP………………MAPI can see a description about the maximum mesh hop in the Mesh Deployment Guide (CVD)：There will be a th...
Dear experts, I had a weird behaviour in a customer site. I tried to upgrade to 8.3.133.0 with the standard version "AIR-CT5500-K9-8-3-133-0.aes" but I was stuck in "Writing new AP image bundle to flash disk" for a very long time ... After 45 mn ...
I could not find any laptop with Intel that supports v5 - they all support up to v4...so I cannot enable MFP - client protection on Cisco WLC. And as far as I can see, even having Cisco MSE with wIPS will not help enough unless MFP is using ccx v5.. ...
