Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi Team, I have a access point (AP2802I) I am looking for autonomous IOS image for this device, when I searched in Cisco site I was only able to get light weight IOS. Thanks in advance. Regards, Saikrishna
We have procured Cisco AP3802E as AP3602E is End of Sale, we need to configure AP in Work group Bridge mode as AP3802E does not support Work group bridge. Which model we can procure which supports work group bridge and which type of Antennas we shoul...
Hi we have WLC 4400. Now I cannot get into it. PC connected to the console port. I press Esc button once it boots. but i do not know why it still boot normally, It cannot show some lines where it gives some choices in order to enter initial configur...
Given below is issue we are facing:Phone A: Wireless G modelPhone B: Desktop 7975G model (CIPC)When phone B calls Phone A, audio is not being transmitted to Phone A. Phone B is able to hear everything phone A says clearly.But Phone A is not hearing a...
Hi, I have a Cisco 5508-12 wireless controller and I would like to change its licensing to "High Availability" so that automatic fail over into a secondary Cisco 5508-12 can occur. It is my understanding that the current per controller 12 l...
Does anyone know how to get into ROMMON for these APs so I can change the flash. It's currently set to Lightweight mode to work with a controller. However, trying to get it to Autonomous Mode to work independently. It's been a bit tumultuous as it...
Hi, I would like to know the purpose of and differences between the following two Software types for the Cisco 1560 Series Outdoor Access Points. Also, can both be used for Bridging between remote LANs? Cisco 1560 Series Unified Mesh Mode Software Ci...
Hi there, I seem to have several outdoor AP's (AIR-CAP1552E-A-K9) that report in Prime Infrastructure to have a lot of clients yet when I check on the AP's directly they is very few. It appears as though Prime is not releasing the data. In one case...
Hello guys, Is there any way to broadcast SSID which use WEP on those Access Points? I know that there is no any reason to use WEP today, but we still need it. Is this hardware or software problem? Maybe in standalone mode(Mobility express)? Thank yo...
i have cisco wlc 2504 with software version 8.2.151.0 , access point 1852 and external dhcp server on windows server 2012 the problem that user when connect to SSID and takes dynamic IP by DHCP he is working fine but for few seconds he disconnected a...
I want to achieve what is on the picture. I have got WLC 2504 and 2 access points 1702. Is it possible?
All, On WLC 5520, when you create LAG, it uses the two 10Gb interfaces. What is the use of MGT port on the WLC then ? first port from left I have used the service port for oob management. What would you use the RP interface for ? Thanks https://ne...
Hello there! Can someone tel me please is there any way i can get access to the end user device that connected ti Cisco wifi controller ? I can see IP address and MAC. May be there is a soft or smthg additionally to install. I need to get cellphone f...
I've installed version 8.3.121.0 as the primary image. The backup image is 8.0.140.0 (default) (active). I have pre-downloaded 8.3.121.0 to 102 of my APs that are supported. The image is set as the backup on them. I have 51 APs that will not support ...
Hi everyone, I have a customer, who request an AP product like : Outdoor can connect to 2 Directional Antennas Both Antennas can transmit 2.4 Ghz Does Cisco have any AP like that? Thank you!
