Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

  Ask Me Anything Event   Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from  Monday,  August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...

sanandy - Parithosh Vema.jpg Pi7_Passport_Photo - Parithosh Vema.jpeg

Hi Experts, I would like to know how many voice clients can be supported in a Cisco 3700 AP?  I have seen a document (Document ID:8103);Q. How many wireless IP telephony handsets are recommended per AP? A. IP telephony network sizing is essential to ...

mcaoile by Level 1
  • 865 Views
  • 4 replies
  • 0 Helpful votes

Hi.Please advice this deployment: Customer has two buildings SITE-A and SITE-B. They are connected by a L3 WAN Service Provider. APs in Site A have the WLC-A as primary, and APs in site B have the WLC-B as primary.  Now the question is:  ( **Since bo...

Soporteco by Level 1
  • 914 Views
  • 5 replies
  • 0 Helpful votes

I have installed the VWLC 8.0.115.0 onto my home ESXi server and am trying to associate a 1131 AP I have read quite a lot about the subject and have tried a variety of images on the AP from the very latest to currently c1130-k9w8-mx.124-25e.JAM4The A...

There are two each WAP2000, one with external/outside antennas in a building with wire network connectivity, the other WAP2000 is a repeater in another building. The repeater is dead due to a failed firmware update. No connectivity, nothing, old IP o...

Hello.I have 3 3850 switches. One is used as MC, two are used as MA. With one of it I succesfully created tunnel, but the second one do not allow me to register points and do not start tunnel. Also on MC I get message:*May 14 2014 06:47:11 EET: *%MM-...

is there someone oft there with experience in Anchor from a 7.6 to the recommended 8 Release? I'd like to give  it a try but some experience is very welcome ;).. cheers, sebastian *******edit*****i made some good experience within the 7.x release so ...

Hello Experts,Wireless controller summary page displays the AP & radio 0 & 1 up/down status.Is there an easy way to find the AP which is affected?Right now I have to go through all the AP's and see the status. Your idea & suggestions will be highly a...

HiIm setting up a Dot1X authentication using ISE 1.3 and 5760/3850 WLAN controllers. The problem is that im not able to match my authentication policy defined on ISE. It jumps directly to the default policy, im using Called Station id= SSID but it is...

Hello Group,my newly deployed Wireless has some little quirks. One of them is that APs on the same Controller (AP 1250 and WiSM) detect each other as honeypot - sending a trap, but than it is nowhere in the rogues (it shouldn't, so this is good) - bu...

Hi!I have a wism2 HA in a VSS, one 6513E and a 6506E - Chassis. Both WISMs are up, running, redundancy is ok etc.etc."show wism status" gives Service Vlan : 260, Service IP Subnet : 192.168.aa.1/255.255.255.0      WLANSlot  Controller  Service IP    ...

Hi all,We have a 1532i Outdoor AP, and inside the building some 2602 AP's all running on a vWLC on the latest firmware.Recently we had complaints that some clients were unable to roam outside where they would expect to get coverage from the 1532.We d...

sossie by Level 1
  • 1188 Views
  • 5 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card