Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hello,AP for branch office registered to the WLC in Main Office, and the AP using flex connect mode.If we see in below picture, VLAN 250, 118, 124, 117, 131 is not exist in the Main Office, only VLAN management 303 exist in the main office.With this ...
How Data traffic will be done between AP and Controller ? Is it go through CAPWAP, I believe CAPWAP used to both control plane and data plane ?
Resolved! EWC on 9115 17.12.03 telnet to APs
Hello colleagues,I'm running Embedded Wireless Controller 17.12.03 on C9115AXI and having issues with this config:ap profile default-ap-profile description "default ap profile" mgmtuser username admin password 0 Admin,12345 secret 0 Admin,12345 ntp i...
Hi Alli'm looking for help and some instructions on how to setup a Home Mesh using 4 x Air-CAP3702i-e-k9 , i do not have a controller on hand , and will be using a Normal POE Injector to power the units up , is there a possible post of guidance on h...
Hey,I’m having issues recovering my Cisco Catalyst 1832i AP, which is stuck in a boot loop and unable to boot from part1 or part2. I’ve tried TFTP recovery, NAND reconfiguration, and direct booting with no success. Here’s what I’ve tried and where I’...
Hello does anyone by chance posess a 8.5.x.x software version of wlc that you can give to me. I have a wlc 8.10.x.x version but it isn't compatible with my access point. Does anyone have it?
Hi,This is my second day at work and this is the first time i am working on a router, so my questions my sound infantile. I hope this community would forgive my ignorance. My company recently bought a C1121-4P Integrated Services Router.It has a USB ...
Resolved! Maintenance mode AP Catalyst 9120
Hi,Question is regarding:* Cisco Catalyst 9800 -WLC* Cisco Catalyst 9120 -APIs it possible to put an AP into a maintenance mode? I want to stop new clients to connect to an AP and make already connected clients to gracefully roam to the neighboring A...
I have recently configured a C9800L. I created an SSID while setting up the Zero Day configuration. That SSID is currently broadcasting via the AP. However, when I tried creating a few more SSIDs, they were not broadcasting. SSID is enabled and broad...
Hi, We have two kinds of SSID networks in our environment. One is tunneled to our Central WLC (Catalyst 9800-40) and the other uses local breakout. For the WLAN that is tunneled, we want to use the same VLAN as for the SSID that uses local breakout...
Hi Guys, just a question, if my laptop wlan driver has been updated to support WiFi6E, does it mean that I can use the same wlan driver to connect to WiFi7 or do I need to update again my wlan driver to support WiFi7?
APBC8D.1F82.E7F0#capwap ap ip 172.16.10.200 255.255.255.0 172.16.10.1 IPC socket server not ready for capwapd. Try after few moments, Errno: 2 Msg_id: 11 APBC8D.1F82.E7F0#
Resolved! IOS-XE 17.16 is out
- Tx for this info @nicolasdarchis on X : > IOS XE 17.16 is out. Definitely a specific release for specific features only. No wifi 7 support yet in it. IOS 17.15.2 should be preferred in all cases. 17.16 is the first release that drops th...
I switched the embedded controller interface to layer 2 and now I cannot access the gui. How do I regain access?
Hello Everyone.I have a corrupt image / boot loop problem on my Access Point - Model 9120 AXIError - verify signature failed for /bootpart/part2/ramfs_data_cisco.cpio.lzmaI recreated the part 2 using below command :(u-boot)> ubi part fs(u-boot)> ubi ...
