Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
So for a long time already I'm considering to change the authentication from WPA2 to WPA3.But, I keep reading here and there, that user's are having more issues with it, or are affected by this change to the worse.Any reasons why it's recommended to ...
Hi Putty console can logon to AP1140 and WLC. Why SecureCRT console cannot work well. Sometimes CRT cannot logon to AP1400 at all. Even if logon to the AP, I cannot type any thing at all. Thank you
HiI was looking for an updated and reliable reference about what 5Ghz channels are usable for outdoor deployment in France or at least in Europe.I'm not talking about mesh infrastructure but about an enterprise deployment.I had a lot of readings and ...
Team,We have configured Cisco ISE with MR46, but when I try to send a session reauthentication request or termination, it does not go through. What could be the reason?Once a user is authenticated, I cannot kick them out of the network. I'm not sure ...
I am going to be replacing a pair of 5520's with a pair of 9800's. My 5520's are in a N+1 design. We did this because it gave me a controller to use for testing configuration changes and OS upgrades. I've read through the 9800 documentation, and I am...
Resolved! CBW150AX Not joining Wi-fi network
I have three CBW150AX APs in my home. Recently one disconnected from the group and was blinking red/green. I upgraded the Primary and second AP to the latest firmware 10.6.2.0. They are working fine. I factory reset the disconnected AP and have be...
Resolved! Learning Wireless from the Scratch
Hello Team,Could anyone recommend resources for self-paced learning on wireless technologies from the beginning? Like,What is dB?How to calculate dB?What are RSSI and SNR?How does signal penetration work over obstacles?Additionally, if we need to mou...
Hello all.Is there any best practice for "DCA Channel Sensitivity", especially for 2.4GHz band?I'm generally cautious about adjusting these types of settings but I would like to know from you all about your experience on changing DCA channel sensitiv...
Resolved! Unavailable reports in MR
Hi, i want to create a unavaliable MR's report about the time that all MR's became unavaliable in the month, then calculate the percentage that it became unavaliable during the month, is there any way i can do that by API? Thank you!
Resolved! Newly deploying wlc9800 at new site.
hello all,This may be a silly question!I am moving one of our site from Aruba to WLC9800. Our internal ssid's are using EAP-TLS and using internal CA. I have configured everything needed I think. My question is how do I test if my internal ssid's are...
How can I check the RP port status on the WLC 9800-L-F controller? I can use the command below on the 9800-40 WLC and it shows whether there is an active link on the RP port, how can I do the same for the 9800-L-F controller?sh platform hardware slo...
Hello , Professionals !!! I have checked the C9800 GUI administration screen, Administration > Management > Logging. It looks like I can set the “logging profile” here,However, the setting was not reflected in the configuration, and there was no in...
What is the best way to create a secondary network on the cisco 9800 to use a different default gateway than the default vlan1 network? Would vrf on the upstream switch be the recommended setup?
Hi Meraki Community,I am planning to upgrade the firmware on my Cisco Meraki MR46 access points. Currently, they are running version MR 30.7.1, and the dashboard is suggesting an upgrade to MR 31.1.5.1 (latest stable version).Looking at the changelog...
Hi All,I have read the part of the WLC config guide about rogue containment, but what does it actually do?It says it sends deauth and deassoc frames to clients of rougue access points. This to me actually seems like we are performing a DOS on another...
