Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hello Experts, I have LWAPs and WLC installed in my company. few of my wireless clients get disconnected from the network without any reason, and they do not auto reconnect unless they manually reconnect to the SSID. This issue just started a couple...
Hi Team, Please if someone can answer this. MSE is appearing as offline/ Unreachable from PI we need to put user/ pass again in prime for MSE and it again start appearing reachable. MSE running on Version 8.0.110.0 PI running on 2.0 With Regards Bini...
Hello all, I am going to one our companies remote sites to install a wireless access point card into a Cisco 2851 router. I have never installed one before so I read the 188 page manual and my head is spinning. It shows you how to do everything u...
Hi Team, Last Reset....................................... Software reset Last Reset....................................... Power on reset Am I correct that the first is due to a soft reset via CLI or GUI and the latter is due to power loss? I just g...
Hello, I have a client with a 2504 WLC with both local and remote access points. The remote access points are 1040s across a 10Mb MPLS. When rebooting the remote APs, it can take anywhere from 15 minutes to an hour or more to complete registration....
Is there a way to see who is consuming the bandwidth most using the GUI or CLI in Wireless Controller, without enabling Netflow? Either finding the IP add or MAC add will work. On a switch, I can easily do this by using "show interface summary" and i...
Hi, I've struggled for some time now getting a Chromecast working over a controller-based wlan. It works perfectly over an autonomous AP, but not over the WLC. I see from several howto's and other posts people have actually gotten this to work, but a...
Hi everybody, I have the similar issue. When trying to make a backup with FTP server, I get this message: CiscoPrimeI/admin# backup BackupFileName repository bakcupCPI% Creating backup with timestamped filename: BackupFileName-151210-1437.tar.gpgBa...
Hi we are going to do a maintains of upgrade of our WLC the downtime could last for a long time as we have 7 wlc. we was thinking if we can convert few ap as an independent ap connected to poe switch so least the critical ares keep up and running if ...
Dears , kindly share your important views ASAP AP1700 series is compatible with Cisco WLC 2504 software version 7.6.130.0 appreciate your kind support. Regards,
Hi, I have one cisco aironet 1200 and i want to connect it to radius server NAC, what i want to ask is when user connect to Wireless SSID and didnt meet the compatibility with NAC they will go to remediation vlan that NAC configured, and if meet the ...
I have a AIR-SAP2602IA-K9 access point that is loaded with 15.3(3) JBB (ap3g2-k9w8-mx.153-3.JBB). I have ap3g2-k9w7-mx.153-3.JC copied into flash (15.3.3-JC) but cannot seem to get it to load. In ROMMON, I set the BOOT variable to flash:/ap3g2-k9w7-...
Long story short I have some older aps that can't go past 7.0 code. While I'm waiting for those to be refreshed I need to provide those areas with guest access. I've attempted to set up LWA with the external authentication page coming from ISE, and t...
Using ipswitch's WhatsUpGold product and we have netflow working from ASA firewalls and 2900 series routers perfectly. I wanted to see if the 5508 WLC could work in this same way, so I configured it but WhatsUpGold shows 0 flows per minute (basicall...
Go myself a couple of APs old 1240AG. When I connect them to POE they boot, but end in flashing ethernet, radio but more conserning the status LED is blinking red amber green. I could not find it any manual. Can someone point me in the right directio...
