hi, I'm using Cisco WLC 2504 with 4 SSID in our company. When I try to connect second SSID by using Iphone, it showing an error like "unable to join to the network". If I completely forget the first SSID, then I can connect easily to second one. I t...
Configuring mDNS on WLC 7.4 posted by Nayarasi in WLC features refers to WLC 7.4 code Cisco supports Apple Bonjour GW.I have looked for WLC 7.4 and could not find on cisco download page:https://software.cisco.com/download/release.html?mdfid=280954465...
Hi there,I have a router 867vae-w-e-k9 which is supposed to include the embedded AP but the interface wlan-ap0 is missing and in CLI service-module wlan-ap0 command is not recognised, so I cannot set up the wireless. The interface Wlan-GigabitEtherne...
i want to use wireless access point . Adivise me which model using for 100-200 users area 70-100 mAnd which model using for 50-100 users area 70 m.
Hi,My name is Francisco and give support to a small hotel that have some access points, and one is a AIR-CAP1602E-C-K9 with the serial number FGL1915X2HU.The problem that i have is that i can not configure because gives an error - "config load from f...
Hello, I run into some issues with powering few AP 1702i . Data sheet stated the power cons. 15.4W Which the Pwr injector : AIR-PWRINJ5 should do. The POE requirements are 802.3af. However in real world when running both radios (2.4 and 5 GHz) the 5...
Hello, I have wireless Cisco Router, model number EPC 2425, which has a NAS device attached to it. I'm trying to find the IP address of the NAS device. Any help would be appreciated. Regards,Stephen
Hi, is firmware version 5.60.22 still available for the CB20A?i have followed the following link,but im getting no higher than 5.60.21, and within the bundles im going lower that mentioned.http://www.cisco.com/c/en/us/td/docs/wireless/wlan_adapter/35...
Dear All, I have created a AVC profile to stop youtube browsing, however don't see it blocking any youtube traffic. Had done it quite many times in the past and it used to work fine. Have tried different codes: 7.4, 7.6.130.0 & 8.0.110.0 but no luck...
Hi Everyone, I am configuring customer Wifi Visitor network.WLC is connected to Switch and Switch is connected to ASA.WLC,switch and ASA all have management vlan 10.Switch has its default gateway set to ASA. wlc---------------vlan 10----------------...
We are configuring a small area for wireless. I have one 3650 configured as a MC, wireless/dhcp works fine. I'm attempting to add another 3650 as an MA to this config with a few APs connected to it but running into some issues. Is there a list of pr...
I am using Cisco prime 2.2.0 versionI get lot of Security Penetration alerts and DOS alerts as critical.I donot want to acknowledge this and Can anyone please let me know what needs to be done how to avoid these kind of alerts? Thanks,Abi
We have a 4402 that is currently using machine authentication for radius. Does anyone know how we'd switch it to use user authentication?
have installed AIR-CAP2702I-K-K9 with power injector and WLC.AP is power on.INjector has AC POWER & AP POWER LED is on.But switch port state is not connected. Not ethernet cable problem.Power injector is fault?
Our network has different vlans One ubtrusted VLAN was used as Wifi network.In this Vlan was a Apple airport whice was used as accesspoint for multiple wifi devices.There are also 2 wifi printer that support wifi direct. After changing the airport b...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-06-2026 09:29 PM | ||
| 08-05-2026 05:58 AM | ||
| 07-15-2026 08:23 AM | ||
| 06-12-2026 07:30 AM | ||
| 06-09-2026 09:37 AM |
| User | Count |
|---|---|
| 9 | |
| 7 | |
| 2 | |
| 1 | |
| 1 |
