Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

5GHz 11N Yagi

Hi AllIs there a yagi that I can use to provide 11N coverage within some racking in a large warehouse under the 5GHz band. I understand there is one for the 2.4GHz.ThanksSimon                  

s.vosper by Beginner
  • 1026 Views
  • 12 replies
  • 0 Helpful votes

Resolved! Repeater ssh/web configuration interface not reachable after performing antenna-alignment scan

Hello, we have a couple of AP1262N-E-K9 APs with firmware version 12.4(25d)JA1 operating in autonmous mode. One AP is setup as repeater while all others are in root mode. The repeater has setup one parent MAC address so it associates every time to th...

dbfokusde by Beginner
  • 770 Views
  • 7 replies
  • 0 Helpful votes

Cisco Prime NCS

Hi Guys,I have few APs showing "RED" in NCS map but when I click on them I can see they're associated to a controller and clients are associated to them as well.Also when I logged into the controller itself and run the command : SHOW CLIENTS SUMMARY ...

Reporting problems with Cisco WCS

hi all,I was wondering whether anyone has experienced the following symptoms on Reporting.WCS Rogue AP reports do not run and show up as 'Expired'this does not occur to all the Rouge AP  reports though (they are being created based on floor areas; on...

AP can not join to WLC after power failure.

We have cisco wlc 2125 with 13 AP 1131g. All works good. But after power failure one AP can not join to controller, only reset help to recover connection AP to WLC. Additionally, we don't have access to rs-232 port on AP. In this moment on WLC we can...

Alex M by Beginner
  • 1068 Views
  • 2 replies
  • 0 Helpful votes

workgroup-bridge unified-vlan-client

Hi team,We need to use this workgroup command in AIR-AP1242AG. This AP comes with the default IOS c1240-k9w7-mx.124-21a.JA1, but this does not support the command.I tested too with IOS c1240-k9w7-tar.124-25d.JA2 without success. Any of you knows abou...

Cisco Wireless network - more load on SSId

hi We currently have created a wireless SSID to accomodate about 1024 users . We are expecting more load on the wireless infrastructure with more devices connecting to it ( more laptops and Iphone devices are being rolled out).Is it better to increas...

TGF_Cisco by Beginner
  • 323 Views
  • 4 replies
  • 0 Helpful votes

2504 WLC reboots when AP attempts to register

hi, I have 2504 WLC with 1142AP. Currently i am starting the deployment. today when i was registering my first AP to WLC. WLC starts rebooting continuously..without any AP registration its stable and i can access the GUI.WLC2504 : 7.2.103.0AIR-LAP114...

nareh84 by Participant
  • 380 Views
  • 3 replies
  • 0 Helpful votes

2504 software update

HiI have just bought a new 2504 WLAN controller and 2x 2602 lightweight APs. I can't get them to talk because the controller has v7.2 software and needs to be at least 7.3. The unit has a mfg date oh Oct 12. Is there a way to get the upgrade with it ...

Resolved! MSE and software compatibility matrix

Hello,I know the document at http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html for the wireless compatibility matrix.However it is not clear and especially table 9 (MSE).Table 9 says that ...

huettep by Beginner
  • 1593 Views
  • 1 replies
  • 0 Helpful votes

Roaming problem with WLC 5508 with Phone 7921

Hi to all,i have one WLC with several AP1231 2.4 GHz. Everything works fine with PC and 7921 in normal condition (last firmware release 1.4.3.4).But with 7921 there is a little problem: if i walk quicky along the warehouse and along lanes while i'm a...

cmaiolani by Beginner
  • 3545 Views
  • 4 replies
  • 0 Helpful votes
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers