Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Dear All, Please help to assist me, I would like to upgrade Wireless LAN Controller Software for my Cisco 5508 Wireless Controller.So I want to know what should I do and check before I upgrade because I already got failed with my last Controller.http...

hengvichet by • Community Member
  • 1903 Views
  • 4 replies
  • 0 Helpful votes

Any device looking for wireless network transmits probe requests to find nearby access points . The access points in turn forwards the probes received to wifi controller. Cisco's mobility service engine(MSE) gets these probe requests forwarded to wif...

seemanagar by • Community Member
  • 688 Views
  • 1 replies
  • 0 Helpful votes

Hi, we have a wireless controller 2500 series and 10 AP's inside the controller's GUI, I can't find the section where I can point the controller in a proxy server so that it hasa certain security filters especially for users browsing the internet.Tha...

TECH-JEFF by • Level 4
  • 1874 Views
  • 3 replies
  • 0 Helpful votes

Resolved! FlexConnect

Hello, Experts! hospital envi2 WiSM2's...1 WiSM2 maxed out 1000 AP lics... the other 50% AP lics used.no redundancywill flexconnect help, as a temporary solution, in case of WiSM2 failure? 

Hi guys.We provide wireless with a couple of Flex7500 in HA Deployment. Both WLC are in LAG (10Gx2) to a Nexus 7K. Management and Redundancy-Management Interface are untagged while in N7K their subnet IP belongs to VLAN1. (I know VLAN1 is not a best-...

gtognin by • Frequent Visitor
  • 647 Views
  • 1 replies
  • 0 Helpful votes

We have a 2504 controller running version 7.4.130.  Need to create a new WLAN that is NOT put in the default AP group and broadcast on all AP's, but the 2500 is restricted to 16 WLANs, can only use ID's 1 through 16, the first 16 WLAN IDs are automat...

Hi Team,We having some issue with the wlc 5508 after configuring the initial setup it saved and ask for reboot but after it reboots again it is asking for the initial configuration again.It is repeating the same Please help on this issue.Regards,Arun

dc-csa-chn by • Frequent Visitor
  • 2659 Views
  • 3 replies
  • 0 Helpful votes

 Have 1142 LAP AP's installed in each floor,  All AP in One specific Floor are rebooting. After reboot most AP are joining WLC but few are unable to Join WLC. Logs in WLC shows AP has Crashed due to "Unexpected exception to CPUvector 2000, PC = 0x49D...

moorthyk by • Community Member
  • 1128 Views
  • 4 replies
  • 0 Helpful votes

dear all, kindly guide me  how to configure WLC 5508 internal DHCP  per WLAN basis , i read the following document it is clearly mentioned that we can configure DHCP on WLC 5508 per WLAN basis. but i did not find the configuration  per WLAN basis htt...

sajid gul by • Community Member
  • 1044 Views
  • 2 replies
  • 0 Helpful votes

Dear All,After upgrading prime to version 2.2 from 2.1, also MSE from 8.0.100.0 to 8.0.110.0 we are unable to see rogue ap, rogue clients, interferers etc.Only heat map is getting generated. CAS & WIPS services are showing 'in sync'   

Review Cisco Networking for a $25 gift card