Hi !What type of band does you can recommend to use? Only 2.4 ? or only 5.0?I know that 5.0 its more faster than 2.4 but, what happens with modern devices thats only has 802.11n?, they will connect to the WiFi or may present problems?We use an WLC 44...
HelloIt is possible to configure SNMP in an AP lightweight with WLC 5508 to get some information with snmpwalk as a AP Serial number? Thanks for your help Regards
Dears,We have a wireless infrastructure here using a WLC5508, and APs 2602i, 2602e and 3702e.Some users complain about signal strength as per below...Sometimes they really get a low signal... 2 or 3 bars..... When I saw at Controller,even when they a...
I am trying to find information on whether it is possible to setup bridging between two lightweight AIR-CAP1532E-A-K9 units and NOT have the traffic be sent back to the WLC via capwap tunnel. My goal if possible is to keep the traffic local to the A...
Hey all, I have a project coming up where we were going to replace some aging 4402 WLCs with 5508s running newer, 7.4.121.0 code (possibly even newer). Due to costs we were considering leaving the 1252s in place until we decided on 3602i/3702i, but 1...
I would like to download the FUS software, delay the reboot, and then download the WLC software and then do the reboot. Is this a ok practice or is it a no no?Note: My controllers are also setup in a High Availability group.
Hi Everybody I look after over 40 5508s WLC and we have upgraded a few of them to 8.0.110. We have had 2 in the last week die. when I say die I mean we loose everything the units no longer even respond on the console port. Both of the controllers ...
We have a AIR-WLC2112-K9 with several access points.Some clients are not able to connect and we can see that they are trying to connect to 802.11b and are in status Probing.802.11g clients are connecting normally.Does anyone have an idea what can be ...
Hello, We have 4 3602 APs (AIR-CAP-3602I-A-K9), each with the AC module installed (AIR-RM3000AC-E-K9). We have these hooked up to Catalyst 3850s acting as the wireless LAN controller. The AC module is not being detected on any of the APs. Everything ...
Looking for help with Asset Tags reporting inaccurate locations. Most tags are reporting 100' more or less from their actual location. We are Using Cisco Prime 2.1.
Hello,I need to develop a solution of wIPS, but I'm not sure about the compatibility between the MSE and the WLC. My WLC is in 7.6.100 version and the MSE is 3310 model. Reviewing documentation, the MSE can only update until 7.3 version. Somebody kno...
The fun just never ends with PI. Now with 2.2, I can create templates all day long. When attempting to "deploy" any of them I get the the attached error. Anyone seen this? Same error message every time in Converged View- works in the deprecated Class...
Hi all,we have a Cisco Prime 2.2.0 and a redundant (SSO) WISM2 pair (8.0.110.0) and about 700 APs.After conversion to redundancy of WISMs and because of different local configurations of some APs we have to change the IPof the primary and secondary c...
Hi Guys;I am after some help in trying to identify what WiFi inverted and WiFi Invalid channel alarms are, I have read the post which gives a good explanation:https://supportforums.cisco.com/discussion/11308356/wifi-invalid-channel-wifi-inverted-spec...
We need a solution for the wireless network inside the campus area for our new project. Our requirement is we have a datacenter inside the campus. So the users standing anywhere in the campus area should be able to access the application which is ru...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 10-15-2026 05:58 PM | ||
| 10-12-2026 06:46 PM | ||
| 09-30-2026 07:34 AM | ||
| 08-10-2026 11:32 AM | ||
| 08-06-2026 09:29 PM |
| User | Count |
|---|---|
| 5 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
