Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
We are trialing google glass in our healthcare environment and the glasses are dropping connection every 30 minutes network wide for about 10 seconds which breaks the data stream. Google glass is legacy G only radio and I have ap's with two slots ...
I'm trying to come up with a list of configuration changes that cause an AP to reboot. This will help me know what types of configuration changes on either the AP and/or WLC that I can perform that will not cause a reboot and do not have to wait to p...
We have about 100 Flex Connect APs spread across a few dozen sites running on a dedicated Flex Connect controller. Periodically, an entire site will lose the ability to use the Guest SSID. The symptoms are:- Client connects to Guest- Client obtains...
Hi I have installed cisco Mobility Service engine, but I cannot access it thru the gui https://[ip address]if i type https://[ip address] I get the certificate errors but the i get an errorForbiddenYou don't have permission to access / on this server...
Uhhuh. NMI received for unknown reason 2d.Do you have a strange power saving mode enabled?Dazed and confused, but trying to continue I replaced the power supplies and hooked up console but see this message on the box.. TAC didn't want to replace it ...
Hello, i have a problem where when AppleTV and other remote clients connect to AP they can't communicate with AppleTV. If ApplTV and clients connect to some other non Cisco AP it works fine. I have no experience with AppleTV so is this maybe a known...
Hello Friends ,I get trouble in ise working on vmware . ISE and Prime are running on same wmware and both of them are up . while one of them (Prime) is avaliable , the ISE cannot be reached . Just ISE can ping its gateway not anymore . What is yo...
Hi, I have the new AP 2702i connected on my Cisco Controller 5508 in HA. The 802.11a/n/ac is not activated on these AP modele ( active on the other modele). I don't find how to activate it on these AP. Could ou please help me Best regards Yoann Pome...
Hi, Please help to know if the Date and Time settings is changed in Cisco 2106 Wireless controller will the associated Cisco Aironet Access points will restart ? Will i require maintenance window for setting Date and Time in WLC ? Regards,Dhaval
Hi All i have 5 cisco AP with model 1602, i need some help on how to find out the IODs from the device, the reason to do this is to add all the AP to our solarwinds server, hope you can help, Thanks ! Keith
Hello,I have an ACS 5.4 (radius server), a cisco 3850 3.3.4XE (Wifi controller) and a 7925 IP Phone.I want to configure a WLAN to authenticate my 7925 using MAB (Mac Athentication Bypass).Here is my WLAN configuration:wlan WIFITOIP 2 WIFITOIP aaa-ove...
I'm confused as to how to setup the remote LAN portion of the office extend solution. Do I need to set up this remote LAN with a local interface and have it talk to the controller's internal DHCP server? Or can I set up this remote LAN and anchor i...
HiI am getting started keepalive when i check show wism status.We had rebooted our core switch.After this it happened.We had rebooted with the same ios.Also i tried rebooting the wism.I can console to wism and i can see the management ip address.Also...
Hi, I have two Wireless LAN Controllers 2504 and 8 APs 3502e. The WLCs are running software version 7.0.116.0. The problem is that I don't have the mesh option to configure indoor mesh inside the controller. In chapter 9 of Wireless LAN Controlle...
Hi Is it possible to deploy the Cisco vWLC inside microsoft hyper v? Tried to import the .ova file but hyper-v only supports .vhd. This links states that hyper-v is supported, but I can't find a guide how to deploy it. I would appreciate if anyone h...
