Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! Error Setting Country Code
After a factory refresh on a 3602i, I am no longer able to set the Country to "US"It is defaulting to "AU" and when I try changing it I get the error that reads "error in setting country code."Any thougths on where to start with this?The AP was purch...
Is a monitor mode AP required on the network for switch port tracing to work correctly?Reason I ask is when running a report for OFF network (off wireless) APs, none are coming up.I'm thinking a monitor mode AP might be the missing piece to the equat...
Resolved! Cisco Mesh Infterface Modes
On the WLC under Wireless > (select AP) > Mesh > Ethernet Bridging > (Interface Name), you can set the mode for the interface. (Normal, Access, or Trunk)Can anyone explain exactly what "Normal" mode is? I can deduce Access and Trunk, but I'm having a...
I have a customer looking to use the AIR-ANT2440NV-R= bell shaped MIMO antenna on an older 1242AP. This is to essentially increase signal coverage using hardware already available.They only need the 2.4GHz "G" coverage which this antenna would look ...
Good Morning everyone,I'm trying to get a 5508 (foreign) and a 2504 (anchor) on 7.5 to work with AirPlay. It's a single SSID/subnet, nothing to fancy other then the anchor. The anchor is providing the wlan for internet access, while the clients (i...
Hi.I have a customer that have set up a wireless network for their showroom where they plan to use AppleTV's and AirportExpresses to allow their employees to easily share video and audio with their clients.The employees connect to one SSID (User) wit...
Resolved! Cisco AP 1530
I am looking for Autonomous AP IOS Software for Cisco 1530 Access point but cant' find it.As per data sheet this AP should be able to operate either in controller-based or standalone operation mode:http://www.cisco.com/en/US/prod/collateral/wirele...
Resolved! 802.1p mapping?
Hi All,have any noticed the 802.11p setting on the WLC has changed several times depending on the software code?This is from 7.4.110.0the 802.11p = 5.Will I get 5 or 4?7.4.100.0 The 802.11p = 6will I get 6 or 5?7.2.115.2802.11p = 6Will I get 6...
Hi,See attached imaget to see how things are configured today. We also want to have local switching on Guest wlan in the remote location but have so far been unsuccessful. My knowledge regarding anchor controllers is limited, so I was wondering what ...
Hi,As of now I have our RADIUS server defined in both the WLAN and Flexconnect group. Do I need to define it in both? Which one is primarily used for authentication of users?Regards,Philip
My WLC mode is 5508, code is 7.4.110.0(7.0.230.0 upgrade to 7.4.110.0)One SSID needs web auth,but when the clients connected to this SSID,it can redirect to web auth page, after user login ,login page pop up again. this problem is not happened before...
I want to configure Cisco WLC 2504 with Local LAN static IP and WLC 2504 with DHCP so that APs can be connect with controller.Currently i am using WLC 2504 with DHCP so can anyone suggest how to do that..
Hi all ,We are using 5508 WLC with 7.4.100.0 version and AP's are 3600 .we have configured internal DHCP lease for the clients . We have one SSID with 802.1x auth WPA2/AES encryption .The problem is some 35 of our laptop is not getting IP address o...
I have 2 1131AG LWAPP AP's purchased in the UK connecting to a WLC 5508 in the US that is setup only for Country US. I am getting the above error when trying to add Country GB United Kingdon I get an error that 802.11b and 802.11a are enabled and mu...
I am new to Prime Infrastructure, and have recently deployed a PI 2.0 with a MSE 7.4 for the purpose of Tracking WiFi clients, as well as AeroScout Tag Tracking and reporting with AeroScout's Mobile View. The site where this system is deployed has ...
