Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Dear Friends,I want to installa and configure Wireless Conroller 6608 (5500 series) and connect Aeronet AIR-LAP1262N-N-K9 access points.Pls guide me.1. Can I configure the 1262N AP in standalone mode as during working in CLI mode I...
Hi,i got a problem with changing 1552e firmware to autonomous. i made many times other ap' s firmware change but now something wrong. i installed the tftpd server to machines it s working ok.image is :c1520-k9w7-tar.default. my pc ip address 10.0.0.2...
I have 5 buildings surrounding our main building. None of them are wired for networking. Currently, I have a 1300 bridge in the main building plugged into a network switch, and an external antenna up on the roof that has line of site to each of the ...
Hi everybodySounds like an obvious request. I need to trace some malware and I need to know in detail when each user is associated to an AP / SSID.I can see some Syslog events like SISF-6-ENTRY_CHANGED. Nevertheless, I see nothing that explicitly tel...
Hi everybody!!I have a AIR-WLC2112-K9 (Software Version 6.0.199.4). Also, I have five AIR-LAP1242G-A-K9 controlled with WLC.I want to add to these deployment AIR-LAP1261N-E-K9. My WLC works only with LWAPP-enabled access points. But this 1260 series ...
After configuring the AP (hopefully it's correct), I have multiple devices such as phones, laptops, touchapds that detect the same SSID twice. For example, my ssid is CISCOCONNECTthe device will detect two identical ssid however one is an open networ...
After the change i save the configuration and reset AP, but it sill reconnected to controller 1. My task is to move about 100Ap from WLC1 to WLC2. Any idea why it connected to wlc1 not wlc2. What is the easitest way to do this?ThanksRay
Initially the controller was running 7.0 with no issues. 1131 AP’s and 1200 series AP's. Additional 1602 AP’s installed and old 1200’s removed (unsupported beyond 7.0.x). Upgraded the controller to 7.5 and no AP’s can join the controller. The 1131’s ...
normally, we config AP so the client have same subnet which AP connect to switch or modem like this:dot11 ssid <SSID-Name> authentication open guest-modeinterface Dot11Radio0ssid <SSID-Name>no shutdown!interface Dot11Radio1ssid <SSID-Name>no shutdo...
Dear Experts,I have Ciscp Prime 1.3.0.20 update 4. All my controllers are configured with SNMPv3.But I am getting huge SNMP error logs showing that controllers are unreachable on SNMPv2C.Not sure when none is configured with SNMPv2C why prime is tryi...
I've configure a cisco 5508 WLC in redundancy mode. Since yesterday this message keep appearing in the log and no ap are associated with the wlc:*RRM-CLNT-2_4: Dec 13 09:51:48.614: #RRM-3-RRM_LOGMSG: rrmClientProc.c:3016 RRM LOG: Airewave Director: r...
Resolved! 5760 Mobility
Hi AllI'm using a Cisco 5760 with 3.3 code with a Cisco 2504 acting as an anchor. The 2504 is running 7.5 code and has 'New Mobility' (Converged Access) enabled.I can't fine any reference to what ports are now used between the controllers. I'm assumi...
Hi all,Please let me know the purpose of 3G RSVD port available in Cisco 819 Router.Warm Regards,Rajkumar G
Resolved! Wireless coverage
Hello,First of all, sorry for my English.So I know wireless like most of people but I never deployed it in office. In fact I already did it but it a was very basic setup with some APs placed whre people needed access but that's it. Now we need to cov...
HiIn our project already one controller and 90 access points are configured but client want to install stand by WLC.what configuration is to done on both Active wlc and stand by wlc.
