HiWe have a setup of CW9166I Access Point connected to C9800-CL vWLC.We are able to check the temperature of the Access point using the below CLI command,AP149F.430E.DC80#show thermal-control-summaryCPU temperature = 56 CRemote sens...
Forum Posts
We have a c9800-48 controller connect with 93 of c9115AXI, controller monitor by solar wind, AP goes down randomly and rejoin again without disconnecting the session. Alert is similar to below:The following Access Point went DOWN on 27 October 202...
I am unable to access my AP.I have checked my com port and put the same com port in putty but here is nothing showing except black command prompt.Also checked below point Baud rate: 9600Flow control: disabledCharacter side:8Stop bits: 1
We are trying to implement 802.1X authentication with EAP-TLS, I would like to know if using an internal CA, using a self-signed certificate, we can carry out this implementation, if it is not possible, do you know what type of certificate we should ...
Resolved! AP not joining WLC
Hello to everyone,I am basically just a beginner in networking, currently i am trying to join Cisco 3702 to joing WLC 2504I have reseted it to rommon mode, uploaded rcvk image, it booted, after booting, it joined WLC, downloaded new image from WLC, w...
We are to migrate WLC from AireOS to 9800. but we are getting an issue on the delay the client is getting an IP. The setup is WLC with dot1x authn and ISE posture. the comparison is when using 9800, it takes 10seconds longer on the posture assessment...
Hello,I have AIR-CT5520-K9, with AP 9115 series. I have 2 questions; how could I totally enable WIFI 6 features, and if enabled, would that impact current connected users on WIFI 5 or 4?Thank you
Hello friends,our Base network team has started recently to apply nice QoS policy map rules on switch-ports in this big hospital.Honestly I have not much knowledge in that area, but it looks like they want to prioritize voice (Skype for Business) an...
I have a 5508 running 8.5.176.2 with a 2602i.The internal guest splash page is setup to use the consent page for access. When I click the connect button, it tells me that I have an incorrect username and password. It then sends me back to the guest w...
I upgraded my virtual Catalyst 9800 WLC to software version 17.09.04a without any issues. I rebooted the controller and all access points rejoined back to the controller. After the upgrade was completed I next tried to install the ap service pack fil...
Hi We facea problem with LAP1042N terminals, which suddenly try to register a bad controller after running normally.They are on a 2500 controller and we have installed a C9800-CL to migrate to new access points on site.The addition of new terminals i...
Hello all, thanks for the quick advice if you can. It's been years since I've set up a pool. The basics are done - but what options do I need to point all my 9120AX APs to my new 9800 controller?IP is 172.16.5.5 for the controller.
Resolved! PoE on C9800-L is not working.
Hi All,I am creating a test bed using IOS-XE Wireless controller C9800-L and C9120. I want to provide PoE to C9120 using port TwoGigabitEthernet0/0/0 of C9800-L but unable to find any documentation to enable PoE on C9800-L. I remember commands like "...
Hi,is there way in a LW deployment to have the 9120 announce themselves via BT? This would be the serial number or the AP name (preferably).I don't seem to find a doc that explains if and how this might be done.Would you have any reference on this to...
How do I get Release 8.5.182.0 if I don't have a contract? for my Cisco Aironet 3800i AP access pointI bought the AP as second hand for my home laband I need this version to support another AP AIR-AP3800-K9-ME-8-5-182-0.zip
